|
||
Thread OP
|
Quote:
Now your frame full unbreakable. Aluminium hex spacer hard to find parts for me. |
|
|
||
|
|
|
|
Widelec,
How is the cutting of new parts progressing, I'd like to get my upgrades / spares underway before Xmas If possible. Sorry to be a pain... |
|
|
|
|
Thread OP
|
|
|
|
|
|
|
Hey, I might put in another order too! I would like a bottom plate (The large one for the motors and whatnot) with 45mm screw holes and extra bottom and top plates (Also 45mm) to protect the electronics and to make it easier to fit a battery on it. I can pay for it next friday, just send an invoice later to my email.
Still working on the frame over here, just mounted and soldered the power spider and all the ESCs, but I'm all out of M2 screws so I can't mount the motors until tomorrow. Doh. >< |
|
|
|
||
|
Quote:
|
|
|
||
|
||
|
Quote:
This is what it looks like right now, can't continue without M2 screws and lock nuts for the motors- =/ Hopefully it'll be finished by tomorrow evening, if I can find any M2 screws that is. |
|
|
||
|
|
|
Me too for an upgrade kit plz
|
|
|
|
|
|
3 more motors to solder. My FPV gear came for my FPV nanoquad though so I need to focus on that for a bit. This quad is coming out real neat though. Everythings protected. Real tight with the 10a Plush ESC's so I'd recommend the 6a's unless you want to remove the shrinkwrap and solder your motors etc. I believe I'll be doing that.
Great looking frame though. Whats cool is, from the side, the power distribution and ESCs are held up in the middle of the quad suspended from 10mm standoffs I had lying around, so the ESCs are soldered and also are suspended. Looks fantastic thats for sure. My coolest quad frame yet I'd say. When I get back to it, lighting time. Lighting strips don't work too well with these, so I'm going to try and shove my 6 SMD LED panels in there and see how they light up the frame.... Great job Widelec and great price as well. My favorite nano frame yet out of 3! Can't wait to see how she flies with copter control. Going to try and tune my Quadrino for it or maybe even my ardupilot mega this thing is so light! The orange Spektrum Knockoff receivers have blue circuitboards as well, so it should look good with both black flight controllers and the blue receiver. I may reheatshrink the ESCs in black. |
|
|
|
||
|
Quote:
The Photoship One Distribution board fits as well and is smaller than the Minsoo Kim board so less cutting of ESC wires. |
|
|
||
|
|
|
I know frosted glass ( even plastic ) transfers light really well. I'm still waiting on my frame ( I live in AZ, I'm wondering why everyone has there's but me ), but I was thinking about finely sanding it just to scuff it up enough that maybe an LED would transfer through.
|
|
|
|
||
|
Quote:
|
|
|
||
Thread Tools | |
Similar Threads | |||||
Category | Thread | Thread Starter | Forum | Replies | Last Post |
Discussion | BambuCopter *BlueBird QuadCopter, BlueBird TriCopter* SmallQuad 450 AirFrames | Widelec | Multirotor Drone Talk | 343 | May 25, 2013 03:00 PM |
Discussion | HK has a new mini quad frame | Pintac | Multirotor Drone Talk | 20 | Sep 28, 2011 10:04 AM |
Sold | Quad frame for sale!!! previously listed. as full quad. | tc3wins | Aircraft - Electric - Multirotor (FS/W) | 3 | Aug 25, 2011 08:56 AM |
Sold | Mini Quad with G10 frame RXR | tc3wins | Aircraft - Electric - Multirotor (FS/W) | 4 | Jul 21, 2011 11:05 PM |