|
|
|
I´m using JR RX so there is no way to connect FUTABA end too it. And yes I did checked and even switched them
|
|
|
|
|
||
|
Quote:
yes, that´s correct! only connect the signal to prevent a ground loop. otherwise the loop is: battery - esc - osd - rx - bec - battery (minus-wires). cheers Thomas |
|
|
||
|
|
|
Does anyone suceed to use a compass with osd ? Gps based heading is kind of useless with heli & multicopter when hovering or flying slow.
I'd really like eagletree realease a protocol trought serial to receive flight controler sensor data ( Compass, Gps, attitude ). We already have good tilt compensated compass data in multiwii or others, why not let us using them ? |
|
|
|
||
|
Kip,
They are working on a x-copter project. I don't know any details, but it is in its' infancy stages. Quote:
|
|
|
||
|
||
|
Quote:
|
|
|
||
|
|
|
Hey all,
Trying to get my fpv setup reliable and bulletproof and have had problems with cheap sunsky video rx and uhf interference. I ended up getting 2 x new 1.3ghz racewood rx from RMRC to fix this problem. I just tested them both and with these video RX with my eagletree osd i get a blurring/ streaking of the white of the text across the width of the screen. if i plug my sunsky rx back in, looks perfect. Any ideas what this could be? I've attached pics so you can see what i mean. Thanks heaps! |
|
|
|
||
|
Quote:
Set OSD Text White Level: Adjusts the white level of the OSD Pro text and graphics. Normally, this does not need to be changed from the default setting of “7.” However, if you see “white streaks” or other anomalies associated with the text display on your video screen, decreasing this value may help. · Set OSD Text Black Level: Adjusts the black level of the OSD Pro text and graphics. Normally, this does not need to be changed from the default setting of “4.” However, if you see “white streaks” or other anomalies associated with the text display on your video screen, increasing this value may help. |
|
|
||
|
|
|
I've got the ET up and running and am starting to play around with it. Is there any templates for info positions? or is it just a case of adding it all my self? Also how do i add the graphical readouts? i can only add numerical at the moment.
I also went to run the servo wizard but it asked me to set the cruise throttle and servo positions. How do most do this? Just make a note of where they hold sticks for the desired speed? and will it matter if i disconnect the motor for this process, (doing this in the house after the kids go to bed and although i love the sound of a brushless motor winding up, my family strangely doesn't share the same love at 10pm) |
|
|
|
||
|
Quote:
You set the stick like you would when you are cruising, don't worry if this is not perfect, when you go fly you can go into a cruise and then go into menu and reset cruise postions, disconnecting the motor is fine, Dion |
|
|
||
|
||
|
Quote:
|
|
|
||
|
|
|
Are we able to change the ft/km to read as miles yet?
|
|
|
Thread Tools | |
Similar Threads | |||||
Category | Thread | Thread Starter | Forum | Replies | Last Post |
For Sale | BRAND New CP Pro/with extra battery | stgtech2 | Aircraft - Electric - Helis (FS/W) | 0 | Sep 06, 2006 09:35 PM |
New eolo pro glitches with cc60 | aschen | Electric Heli Talk | 24 | May 20, 2004 08:12 AM | |
FS New Piccolo Fun with bearing upgrade and HA tail motor | Bud Morrison | Aircraft - Electric - Airplanes (FS/W) | 1 | Mar 21, 2004 07:32 PM | |
For Sale: NEW Pic Pro rotor head with stiffening mod | Eco8gator | Aircraft - Electric - Airplanes (FS/W) | 2 | Jun 02, 2003 09:16 PM |