Thread Tools
Aug 12, 2012, 12:42 PM
Stirring the pot
johannlochner's Avatar
Thread OP
Quote:
Originally Posted by Sean Oelofse
Reminds me of the Model T Ford.....................You can have it in any color!....as long as its Black!
Hehehe
Or.....
Carbon!
Sign up now
to remove ads between posts
Aug 12, 2012, 09:38 PM
Egads! It's a GIRL!
Lil Stinkpot's Avatar
Ooohhhh......

http://upload.wikimedia.org/wikipedi...r_Goldfish.jpg
Aug 12, 2012, 09:44 PM
Gliders ain't drones!
Zenmaniac's Avatar
Quote:
Originally Posted by johannlochner
Hehehe
Or.....
Carbon!
It's 4:42 AM in PE, and the light's on.
Must be seriously thinking of colors!

-= Dave
Aug 13, 2012, 02:06 AM
sand it - round?
Vic101's Avatar
Hey J,

That edge repair on the mould at the fin came out superbly! How did you do that? Looks like you gel-coated the entire area, did you then "just" sand back the excess gel-coat?

Impressive how you maintained the edges and the rest of the surface

Vic
Aug 13, 2012, 01:12 PM
.....till the wind drops.
Sean Oelofse's Avatar
Quote:
Originally Posted by Zenmaniac
It's 4:42 AM in PE, and the light's on.
Must be seriously thinking of colors!

-= Dave
Naa!
I think its RCG getting there lines crossed!
Aug 13, 2012, 01:21 PM
Stirring the pot
johannlochner's Avatar
Thread OP
Quote:
Originally Posted by Sean Oelofse
Naa!
I think its RCG getting there lines crossed!
Naa....
I was up!
Getting ready to gallivant around the country side!

It's easier than is looks Vic!
Just try....
Last edited by johannlochner; Aug 13, 2012 at 01:24 PM. Reason: J..... Rubbing his eyes!
Aug 13, 2012, 01:23 PM
.....till the wind drops.
Sean Oelofse's Avatar
I hope you where on RCG while brushing your teeth?
Aug 23, 2012, 12:33 PM
...missing the PE Slope Rebels
Flying Beagle's Avatar
Hey J !

whats happening ?

70's What's Happening Intro (1 min 2 sec)
Aug 24, 2012, 05:21 PM
Stirring the pot
johannlochner's Avatar
Thread OP
Quote:
Originally Posted by Flying Beagle
Hey J !

whats happening ?
Blowing Bubbles!

Well I finally received my stash of composite goodies....
Soooo...
I suppose I have no excuse!
Last edited by johannlochner; Aug 24, 2012 at 05:24 PM. Reason: Hoping my bubble won't burst!
Aug 25, 2012, 12:07 AM
What goes up must come down
aimrah2000's Avatar

My DLG


Hi Guys:
Ckeck out my latesd bird
Aug 25, 2012, 12:10 AM
What goes up must come down
aimrah2000's Avatar

Mig


From the other day at Maitlands
"A Good Day"


A good day at Maitlands final (3 min 0 sec)
Aug 25, 2012, 12:42 AM
Gliders ain't drones!
Zenmaniac's Avatar
Quote:
Originally Posted by aimrah2000
Hi Guys:
Ckeck out my latesd bird
Quote:
Originally Posted by aimrah2000
From the other day at Maitlands
"A Good Day"
Isn't this a Goldfish "build thread"??

Mmmm... I can smell the epoxy tonight!

-= Dave
Aug 25, 2012, 01:53 AM
Stirring the pot
johannlochner's Avatar
Thread OP
Quote:
Originally Posted by aimrah2000
Hi Guys:
Ckeck out my latesd bird
I smell something....
fishy!

It's all a planned
Conspiracy!!!
Last edited by johannlochner; Aug 25, 2012 at 03:16 AM. Reason: J, who is not really from this planet!........either.
Aug 25, 2012, 12:03 PM
Stirring the pot
johannlochner's Avatar
Thread OP
If you don't prepare well, things will go wrong!

What can I say...
I must have got fish eye in the clear coat as it only showed up once I got the finishing coat on.
I let it dry and sprayed again. It should be OK.

The lay-up went no better......
I need to re look the templates too. They stretched out all over the place.
There are to few clamps, and I think I lost a Mylar spacer during the resin evacuation because the one edge can't close down tight!

That, between fetching my daughter, the gardner wanting to go home and my wife muffed because I never went with her......
Having said all that,
It just could be OK!
Aug 26, 2012, 01:43 AM
Graham Kirkland
graham1234's Avatar
It always takes a coupe of tries before you get it right.
There is always a market for the seconds.
At least the bladder did not burst - that will make a right mess

Looks like I better get onto those wings pretty soon

Graham


Quick Reply
Message:

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion First Fun Fly of the year at Hartford Pa. 3/16, 3/17, 3/18. 2012 Curt S RC Flight Events 0 Mar 14, 2012 11:08 AM
Contest 2012 New Years Day Postal Contest Mr B.... Sailplane Events 115 Jan 08, 2012 12:38 PM
Contest 2012 New Years Postal Contest Mr B.... Thermal Soaring 1 Dec 27, 2011 10:03 PM
Discussion 2012 the year of the Hypothecation event bubble bursting making sub prime look small treehog Life, The Universe, and Politics 0 Dec 17, 2011 07:59 PM