Thread Tools
Feb 04, 2009, 10:11 AM
Team Extreme Flight
Doc Austin's Avatar
...........
Last edited by Doc Austin; Mar 27, 2012 at 08:28 PM.
Sign up now
to remove ads between posts
Feb 04, 2009, 10:32 AM
God is my pilot
JimTMich's Avatar
Quote:
Originally Posted by Andrew Jesky
Ben,

One note I want to make is that if you plane to fly on an A30-28s with a 12x6 please make sure you purchase the hacker X-40 or similar. While testing this model I have found that flying these models very hard will cause a shut down and in some cases fire. Just a word of warning.
12x6 on a A30-28S...Wow...that must be for bursts only
Feb 04, 2009, 10:40 AM
ExtremeFlight - 3DHS - Legacy
blucor basher's Avatar
3D is basically that...for sustained full-throttle flying, a smaller prop is in order.
Feb 04, 2009, 11:46 AM
Chesapeake Bay RC Club
Gary Hoorn's Avatar
I wish this had been available when I purchased my 51". Smaller planes go better with my condo and my C240. May have to put the 51" on the block...
Gary
Feb 04, 2009, 11:59 AM
Registered User
pootman's Avatar
Quote:
Originally Posted by chribrian
This Scorpion motor looks very good!!

Scorpion 3008-28

Stator Diameter ............................ 30.0 mm (1.181 in)
Stator Thickness ............................. 8.0 mm (0.315 in)
No. of Stator Arms ................................................ 12
No. of Magnet Poles ............................................... 14
Motor Wind ........................................... 28 Turn Delta
Motor Wire ...................... 10-Strand 0.19mm (32 AWG)
Motor Kv ........................................... 1253 RPM / Volt
No-Load Current (Io) ................................. 1.53 Amps
Motor Resistance (Rm) ............................. 0.072 Ohms
Max Continuous Current ............................... 30 Amps
Max Continuous Power ................................ 400 Watts
Weight ........................................ 85.5 Grams (3.02 oz)
Outside Diameter ......................... 37.50 mm (1.476 in)
Shaft Diameter .............................. 4.97 mm (0.197 in)
Body Length .................................. 25.9 mm (1.019 in)
Overall Shaft Length ....................... 64.5 mm (2.539 in)
http://www.innov8tivedesigns.com/pro...products_id=72

That's a sweet motor. My buddy used it place of a Hacker A30-28S and it was awesome. The motor does weigh about .5 oz more than the Hacker but the power more than made up for it. It also ran very cool.
Feb 04, 2009, 03:16 PM
TDI Abuser
flyinghigh's Avatar
So a 16M should be a more proper motor for this one ? Im wondering cause if you need a 40 on the 28s the efficiency must be going way downhill with that 12x6 ?
I run a X35 on my 16M with no issues , gets me thinking you know .
Feb 04, 2009, 04:04 PM
ExtremeFlight - 3DHS - Legacy
blucor basher's Avatar
16M is over 100g...too big. We don't have any problems with the A30-28S, we've just had problems with the smaller ESCs.
Feb 04, 2009, 04:11 PM
ADC Vinyl
Fliprob17's Avatar
A30-16M seems like a little too much to me......the A30-28S pulls right around 34-37amps & 370-380watts @ WOT on an APC 12x6, depending on the pack. It drops down around 30amps+/- quickly when you get just a click or two off of WOT. The motor seems to handle a quick 5-10 second burst just fine, doesn't really seem to get hot at all.

The A30-28S is about 71grams, while the A30-16M is about 105grams, a big weight increase.

EDIT - Ben beat me
Feb 04, 2009, 05:39 PM
Registered User
3D-Flyer Kevin's Avatar
WOAH! This could be just the plane that I have been looking for. I have a Scorpion 3008-28 that needs a good home.
Feb 04, 2009, 05:53 PM
"Because I was pǝʇɹǝʌuı"
bighead93's Avatar
Looks like a really fun plane!
Feb 04, 2009, 06:37 PM
May the Farce be with you...
refugeefromcalif's Avatar
I just ordered a GR-25, (On Sale), to get ready for this plane. (In Yellow).

George
Feb 04, 2009, 06:39 PM
TDI Abuser
flyinghigh's Avatar
Ok thanks , I was just wondering as I have both motors but been using them at lower Amps/wattages for years . I guess its just the old school thinking with them as the 28s was originally only rated for around 15a continuous and 25a burst .

Thanks . looks like I have everything already then .
Feb 05, 2009, 08:49 AM
Captain Norway's Avatar
Quote:
Originally Posted by The Reaper
hey guys

we have a design for one but in this economy i dont think i will be putting it into production , if you guy want them i would have to do a private preorder and make a limited run of 50 pieces so i would need 50 guys to get together to order them ahead of time. We may end up doing the same thing on the GR60XL

scott
I personally think the GR25 on 3s and 12x6 is more than enough for the 40" Edge, and should do fine in the 42 size as well.

If the GR60XL will work on 7s for the 70ish size planes, I will join in on that.
Feb 05, 2009, 04:31 PM
Registered User
wooooooooowwwwwwwww.damn I didnt need to see this sweet beauty.I cant believe it flies so well on on the park 480.My 480 is just laying in a box and a speed control to go with it.I have instantly decided I want a 42 inch slick.it's the perfect size and affordable!!!nice going AJ and Ben! yes doc this looks awesome ..so sweeeetttttttt
Feb 05, 2009, 04:56 PM
Monday? Not again...
nickflyer's Avatar
I have a A30-28S on my Groove, but I'm running a 10x5 APC. Will that not quite the omph for this plane? Looks really cool, I might have to forego a SHP and just take the stuff out of the Groove.


nick


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Video 3DHS 51" AJ Slick - Cow pasture 3D blucor basher Electric Plane Talk 33 Dec 04, 2010 07:52 PM
Video 3DHS 89" AJ Slick Electric blucor basher Electric Plane Talk 28 Dec 04, 2010 04:31 PM
Sold 3DHS AJ Slick NIB trade for trex 450v2 hairymuffin Aircraft - Electric - Airplanes (FS/W) 3 Oct 11, 2008 08:39 PM
Video 3dhs AJ Slick harrier machine FlopGun Electric Plane Talk 3 Oct 08, 2008 11:04 PM