Shop our Airplanes Products Drone Products Sales
Thread Tools
Jan 15, 2009, 09:56 AM
D'oh.. Dumb Left Thumb
dekan's Avatar
Dan, TM's giving me grief again can't you keep him under control
I am going to build a LPBF but just not yet....
Sign up now
to remove ads between posts
Jan 15, 2009, 10:20 AM
Zippy, Strong Like Bull!
Trouble Maker's Avatar
Sorry dekan I am out of control. Well my flying anyway.

TM
Last edited by Trouble Maker; Jan 15, 2009 at 10:26 AM.
Jan 15, 2009, 10:48 AM
D'oh.. Dumb Left Thumb
dekan's Avatar
TM, I know I'm a slow builder...

I had three other projects on the go at the same time ....

I pushed the Firefly up to the top of the list, as I knew Dan wanted some feedback outside his circle of FB's, in order to help spread the word...
Jan 15, 2009, 11:13 AM
My plans are in my blog
Rusty-Gunn's Avatar
LP... We'll post vids once we get to flying the planes.
GPW... yes, Nic was intrigued by the Nutball, and used it as a basis for his. Adam's and mine use a profile Fireball fuselage (Fireball plans are in my blog).
The two brothers are using them 10 gram brushless motors, and I'm using a small 11.1v brushless, all spinning 5 inch props. They'll use 7.4v 430 lipos, I'm using thesame, but in 11.1v. Servos are about 8 gr size, we're all hoping these set-ups will do fine, having never used them before.
Jan 15, 2009, 05:58 PM
Registered User
kimhey's Avatar
Just started, here it is. Hopefully ready for the weekend
Jan 15, 2009, 06:31 PM
D'oh.. Dumb Left Thumb
dekan's Avatar
It must be nice to find a sponsor for your model...
Jan 15, 2009, 07:26 PM
Winging it ̉>
leadfeather's Avatar
Kimhey, that is some great artwork; very nice!

I see a color marker in the picture. Is that what you used to do this terrific paint job?
Jan 15, 2009, 09:53 PM
Registered User
Ok silly question
is the motor shaft even with the wing ?
or is it a tad above
Marty
Jan 15, 2009, 10:19 PM
Winging it ̉>
leadfeather's Avatar
Quote:
Originally Posted by Marty Slater
Ok silly question
is the motor shaft even with the wing ?
or is it a tad above
Marty
Tad above.
Jan 15, 2009, 10:36 PM
Registered User
Thank you Dan for the come back
an Thank you for your ideas an sharing it with us
did you round off any of the edges wing or fus
Marty
Jan 16, 2009, 01:47 AM
Registered User
kimhey's Avatar
Quote:
Originally Posted by leadfeather
Kimhey, that is some great artwork; very nice!

I see a color marker in the picture. Is that what you used to do this terrific paint job?
Searched the internet for nice logos, and stumbled across this. Printed it in 2X2 (A4-size), taped them together and cut out the letters/bulls with a sharpie... M77 sprayed to the back - stick it on- spray...

(And yes..its not RED, but ORANGE , simply because thats what i had available).

After this operation, I used the the colourmarker.
Jan 16, 2009, 04:21 AM
Winging it ̉>
leadfeather's Avatar
Quote:
Originally Posted by Marty Slater
Thank you Dan for the come back
an Thank you for your ideas an sharing it with us
did you round off any of the edges wing or fus
Marty
Marty, on the wing I rounded the leading edge a little...don't know if it makes any difference but it looks a little better to me.
Jan 16, 2009, 05:41 AM
Registered User
kimhey's Avatar
Now it just needs some rc-gear...
Jan 16, 2009, 06:32 AM
gpw
gpw
“There’s no place like Foam”
gpw's Avatar
That's VERY NICE!!!!!!!!!!!! Time for a Milka PBF...hahahaha
Latest blog entry: Lost plans
Jan 16, 2009, 06:48 AM
Look outside the Square
Boxhead's Avatar
If I could only find my picture of her Mmmmmmmmmm .

B x


Quick Reply
Message:

Thread Tools