Shop our Airplanes Products Drone Products Sales
Thread Tools
Oct 26, 2012, 10:38 PM
Somewhere in New York
byteman's Avatar

asw28


Hi guys .im from NYc im waiting my st ASW28 TO maiden flight.
This is my first glider. I wish that its a nice flier.
Sign up now
to remove ads between posts
Oct 29, 2012, 03:06 PM
Somewhere in New York
byteman's Avatar
Some pictures of my home made glider.
Im waiting until my ASW-28 arrive from tower hobbies....
Last edited by byteman; Oct 29, 2012 at 05:25 PM.
Nov 23, 2012, 08:19 PM
Somewhere in New York
byteman's Avatar

asw28


Hi . Its a good glider.
Dec 21, 2012, 05:08 AM
Registered User
Hi;

@studioRS

May I ask what type of cover was used on the EPP / EPO wings to soften it and give such smooth look, did u covered CA+cottonFiber the hole wing than or just the tipps? did u us an airbrush? I cant find a log for those chemicals used
Martin
Dec 21, 2012, 08:06 AM
Klassische Bilder
studioRS's Avatar
Quote:
Originally Posted by vavo
Hi;

@studioRS

May I ask what type of cover was used on the EPP / EPO wings to soften it and give such smooth look, did u covered CA+cottonFiber the hole wing than or just the tipps? did u us an airbrush? I cant find a log for those chemicals used
Martin
All the details are in my ASW-28 blog here
https://www.rcgroups.com/forums/show....php?t=1494472
Jun 10, 2013, 05:14 AM
Registered User
netarc's Avatar
Quote:
Originally Posted by Goody63
Anyway I decided to change the ASW28 to a 3S setup during the week.

I kept the stock motor and prop but changed the esc to a Turnigy Plush 25 amp. With a 3S 1000MAh lipo the power went up to 145 watts at around 15 amps.
When swapping out the ESC for one that will support a 3S battery, is a 25-30amp ESC sufficient, or did you ultimately find you needed more? Also, brush or brushless ESC? And are you still running stock motor & prop?

Thanks for any advice, I'm considering purchasing the ASW28 but would like to do the 3S upgrade.
Jun 10, 2013, 08:17 AM
Registered User
mikejincan's Avatar
Quote:
Originally Posted by netarc
When swapping out the ESC for one that will support a 3S battery, is a 25-30amp ESC sufficient, or did you ultimately find you needed more? Also, brush or brushless ESC? And are you still running stock motor & prop?

Thanks for any advice, I'm considering purchasing the ASW28 but would like to do the 3S upgrade.
A 25~30 amp brushless esc is more than adequate ... as was just mentioned, it uses 15 amps with a three cell battery. He did say that was with the stock motor and prop.

Be advised, if you go to a 3 cell esc & battery you can't run the motor at full throttle/power for more than a few seconds at a time without burning out the motor.

Adding a bigger esc and battery equals more weight, it's no longer a lightweight glider. If you want a hotliner, buy one, don't try to modify this glider to be a hotliner, buy the fiberglass version .
Jul 26, 2013, 08:38 PM
Registered User
pitts's Avatar
I have owned this model for about 4 years now, but just got it out again the other day. Its a really enjoyable glider to fly, and other than the pilot figure, I have left it stock.
Heres a little vid of the ASW28 sniffing around for some lift (We are in winter here, so there wasnt much around!!!)...

Flight Of The ASW28 (7 min 58 sec)
Jul 26, 2013, 09:05 PM
Biomass processor
cynr100's Avatar
Very very nice vid Pitts, pat yourself on the back.

Hmmmm think I might one
Jul 26, 2013, 10:31 PM
WHAT U LOOKIN AT!
jaskel's Avatar
very nice vid mate
Aug 13, 2013, 02:42 PM
(madkev :) )
kdwzagi's Avatar

wing underside question


Hi
I've had my st models asw28 for over a year now and even though it flies well the underside of the wings always bothered me. the circular moulding that houses the aileron linkage is quite proud from the rest of the wing surface (4mm) and there's a channel that houses a small stiffener outward of this that is quite deep (not full of glue). both wings are the same so i guess they're all produced the same in the factory?

has anyone sanded excess foam from the circular moulding and filled the channel ?

your thoughts please

Kev
Last edited by kdwzagi; Aug 13, 2013 at 02:55 PM. Reason: added photo
Aug 13, 2013, 04:27 PM
Klassische Bilder
studioRS's Avatar
I've been successful removing some of the foam that is near the aileron arm. My best fix for smoothing out was to cover with either white vinyl or clear tape.
Aug 14, 2013, 07:08 AM
(madkev :) )
kdwzagi's Avatar
Quote:
Originally Posted by studioRS
I've been successful removing some of the foam that is near the aileron arm. My best fix for smoothing out was to cover with either white vinyl or clear tape.
when you say some of foam did you remove it so that it was flush or did you just blend it in a bit ?

kev
Aug 14, 2013, 08:04 AM
Went to mow a meadow
frank48's Avatar
Can anyone suggest a replacement motor? Ive hunted high & low for one with a long threaded shaft so the folding prop fits
Thanks
Frank
Aug 14, 2013, 08:42 AM
Klassische Bilder
studioRS's Avatar
Quote:
Originally Posted by kdwzagi
when you say some of foam did you remove it so that it was flush or did you just blend it in a bit ?

kev
Both, I removed some foam (and glue bits) underneath the servo arm so movement was smoother and blended the edges on the outside where they protrude past the airfoil surface, then covered with clear tape.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
HF Model: ASW28 Fully Molded, 3m rthorne Aircraft - Sailplanes (FS/W) 9 Jun 06, 2005 04:09 PM
ST MODEL Lipos? OzDragonFlyer Batteries and Chargers 2 Mar 14, 2005 03:21 AM
Motor for ST model YAK TooLyr 3D Flying 7 Oct 26, 2004 04:17 PM
Any Experiences with ST Model Lithiums? CustomPC Batteries and Chargers 8 Jun 09, 2004 10:15 PM
ST Model KA-V1000R lipo charger jbird Batteries and Chargers 3 Nov 11, 2003 07:38 PM