|
|
|
Bluetooth module JY-MCU BT_ BOARD v1.2
Hey fans of Bluetooth
The module is set to 9600 baud rate by default. On the web site Alejandro Pirola is set this modul to 115200 baud rate. Use the command AT+BAUD8. Other settings are not required. Pins can be connected directly to the transmitter connector. esu-ov |
|
|
|
|
||
|
Quote:
I'm a Bluetooth fan! Willy. |
|
|
||
|
|
|
|
|
|
|
||
|
Quote:
here http://www.sgr.info/usbradioandroid/bluetooth.htm I've written a page describing how to set a Bluetooth module. After the Bluetooth version now I'm going to write an application for Android tablet using the standard USB-Serial adapter. Bye HappyMan http://www.sgr.info/usbradio http://www.sgr.info/usbradioandroid New software for the Hobby King, FlySky, Turborix, Exceed, Storm, CopterX and Jamara radio - V1 and V2 - For Windows, Linux and Android http://www.sgr.info/batterymanager New software to manage your set of LiPo/LiFe/NiMH batteries |
|
|
||
|
|
|
Bluetooth Adapter
This is what I created a while ago.
Use it with Samsung smartphone Works fine for small correction in the field |
|
|
|
|
|
The transmitter board needs a 5V regulated supply, so you'll have to have a 5V regulator and also have to add a bind button.
|
|
|
|
|
|
I had to remove the module form the Turnigy 9x and I now need to re-install it. Is this just a single wire that I can simply solder back onto the board once I get the wire pulled thru the case again?
I can't quite see good enough to make it out. I had no trouble removing it, I think I just cut it at the solder point on the board. |
|
|
|
||
|
Quote:
|
|
|
||
|
|
|
|
|
|
|
|
|
The T6 transmitter board is functionally identical to the stock 9X module. The 9X simply has a JR case and an adapter board which provides a bind button and lets it work with the JR pinout (including 5V regulation from raw battery voltage).
|
|
|
|
|
|
Hi , I tried this mod for one of my CT6B's and it is not working as a trainer, just to be sure you connected the end of the yellow wire going to the transmitter module to the center position of the switch, the end going to the main board to end one and the cut red wire from the trainer port (next to the black wire) onto end two of the switch?
I have scoured the thread and did not find any other discussions on this mod but it has been a very active thread sorry if it has already been addressed and I missed the update. This is in reference to the original post #1697 where directions were given to add a momentary switch to the CT6B to allow it to be used as a master buddy box. Has anyone had any luck with this modification, and if so can you help me understand where I might have gone wrong? Thank You in advance for any useful advice! |
|
Last edited by 77095066; Feb 10, 2013 at 11:38 PM.
Reason: I had omitted reference post
|
Thread Tools | |
Similar Threads | |||||
Category | Thread | Thread Starter | Forum | Replies | Last Post |
New Product | X8---new 2.4GHz Radio System | ASSAN | Radios | 5757 | Jul 15, 2020 05:06 PM |
Yippee! | New 2.4GHz DSM radio - New standard? | PrasadL | Scratchbuilt Indoor and Micro Models | 12 | Jun 03, 2013 07:03 AM |
For Sale | NEW - 2.4GHZ 2 channel Pistol R/C system | SRM | Cars - Cars and Parts (FS/W) | 0 | Oct 22, 2008 09:39 AM |
FS: 1x Used 1x New 2.4ghz Wireless video cameras with receiver | Nik-rc | Aircraft - Electric - Airplanes (FS/W) | 4 | Nov 30, 2004 07:21 PM |