Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Feb 18, 2009, 12:21 PM
tallflyer is offline
Find More Posts by tallflyer
Registered User
tallflyer's Avatar
Quote:
Originally Posted by Yaniel
my outdoor setup which is great in even a small ~7mph breeze is:
all 9mm 1.3#
hxt500's on the tail
eflite s75 on ailerons
1300 kv blue wonder
9050 gws prop
3s450mah 25c 2dogrc lipo (44g)
built with hot glue
auw is ~190g seems like a brick compared to your indoor ones but its great for outdoor use and hovers at half throttle. try it out, you wont be disappointed.
great setup have you tried a 8040 prop? on your setup?
RCG Plus Member
Latest blog entry: Yunnec Typhoon H Review
Sign up now
to remove ads between posts
Old Feb 18, 2009, 12:35 PM
Figure.N9ne is offline
Find More Posts by Figure.N9ne
Registered User
Quote:
Originally Posted by tallflyer
great setup have you tried a 8040 prop? on your setup?

yea thats how i started off, it has enough power but the 9050 gives it a wider power band/range so power modulation is smoother and it seems to give all the surfaces more authority (might be a placebo effect). on the slofy with the 9050 the prop caused too much torque roll on the plane, but the yak doesn't notice it.
Old Feb 18, 2009, 07:02 PM
leadfeather is offline
Find More Posts by leadfeather
Winging it >
leadfeather's Avatar
Quote:
Originally Posted by Yaniel
yea thats how i started off, it has enough power but the 9050 gives it a wider power band/range so power modulation is smoother and it seems to give all the surfaces more authority (might be a placebo effect). on the slofy with the 9050 the prop caused too much torque roll on the plane, but the yak doesn't notice it.
Our group found the same thing. The 1300 seems like a dud compared to the 1500 unless you go with a bigger prop on the 1300.
Old Feb 19, 2009, 02:19 AM
rcolle is offline
Find More Posts by rcolle
Registered User
rcolle's Avatar

Have to Build One


Im waiting on some foam to arrive and I just have to build one of these to see what all the fuss is about (just kidding).
Sounds like an awesome plane. Im all for the 9050 on the BW w 3s.
Old Feb 19, 2009, 09:13 PM
moxjett is offline
Find More Posts by moxjett
Pug Pilot
moxjett's Avatar

Smaller Edge


I scaled back my Edge to a size closer to the Yak. I also didn't like the looks of the bigger Edge's Fuselage, so I changed it a little as well. Mainly changing the looks of the canopy. This one took awhile to finish painting, but I like the looks of the Castrol Edge 540, so it was worth the extra effort. I haven't had a chance to weigh it yet. I'll wait till I get some of the components installed. Hope she fly's as well as the Yak and I'll be pleased.
Old Feb 19, 2009, 09:14 PM
ak49flyer is offline
Find More Posts by ak49flyer
Clear prop!
ak49flyer's Avatar
Very, very nice! That's a winner!
Old Feb 19, 2009, 09:38 PM
adreher is offline
Find More Posts by adreher
Registered User
adreher's Avatar
Mox,

Dude, sweet! I really like that scheme! The edges and lettering are so crisp, awesome! Please post some pics to the paint thread
Old Feb 19, 2009, 09:43 PM
leadfeather is offline
Find More Posts by leadfeather
Winging it >
leadfeather's Avatar
Moxjet, very impressive! I'm looking forward to seeing this one fly; saweeeeet!
Last edited by leadfeather; Feb 19, 2009 at 09:51 PM.
Old Feb 19, 2009, 09:50 PM
moxjett is offline
Find More Posts by moxjett
Pug Pilot
moxjett's Avatar
Thanks for the kind words guys. I'll post the pics on the paint thread as well.

Mark
Old Feb 19, 2009, 09:57 PM
dz1sfb is offline
Find More Posts by dz1sfb
Ken's CAD Models
dz1sfb's Avatar

Skinny Yak change A plans here!


Skinny Yak plans have been updated. The following changes have been incorporated.
  • Angled cut lines on aileron counterbalances 45 degrees.
  • Trimmed 1/8" off the inside edge of elevators
  • Opened radius of elevator clearance in rudder be 1/8" and simplified the cut out.
Ken


Edit: Removed plans and added revision "c" in new post.
https://www.rcgroups.com/forums/show...&postcount=722
RCG Plus Member
Last edited by dz1sfb; Feb 21, 2009 at 09:39 PM.
Old Feb 19, 2009, 09:58 PM
rcolle is offline
Find More Posts by rcolle
Registered User
rcolle's Avatar
Best Looking EPP Ive Ever Seen
Old Feb 20, 2009, 06:34 PM
rcolle is offline
Find More Posts by rcolle
Registered User
rcolle's Avatar
Quote:
Originally Posted by moxjett
I scaled back my Edge to a size closer to the Yak. I also didn't like the looks of the bigger Edge's Fuselage, so I changed it a little as well. Mainly changing the looks of the canopy. This one took awhile to finish painting, but I like the looks of the Castrol Edge 540, so it was worth the extra effort. I haven't had a chance to weigh it yet. I'll wait till I get some of the components installed. Hope she fly's as well as the Yak and I'll be pleased.
by chance will you be posting plans, or starting a edge540 thread?
Old Feb 20, 2009, 06:51 PM
moxjett is offline
Find More Posts by moxjett
Pug Pilot
moxjett's Avatar
Quote:
Originally Posted by rcolle
by chance will you be posting plans, or starting a edge540 thread?
We'll see how she fly's this weekend. I'll probably need leadfeathers help in creating an Adobe file with template drawings on it. I've never created plans before.
Old Feb 20, 2009, 06:55 PM
rcolle is offline
Find More Posts by rcolle
Registered User
rcolle's Avatar
Quote:
Originally Posted by moxjett
We'll see how she fly's this weekend. I'll probably need leadfeathers help in creating an Adobe file with template drawings on it. I've never created plans before.
Ok, Looking forward to it
Old Feb 21, 2009, 07:21 PM
dz1sfb is offline
Find More Posts by dz1sfb
Ken's CAD Models
dz1sfb's Avatar

Edge Plans


Quote:
Originally Posted by moxjett
We'll see how she fly's this weekend. I'll probably need leadfeathers help in creating an Adobe file with template drawings on it. I've never created plans before.
Mark,

I have been generating Leadfeathers plans for him. Your Edge looks really great. Nice paint job! Dan usually supplies a dimensioned sketch, photo, or scanned hand drawn image files. These aircraft are fairly simple to generate drawings for, so, I will help if you want.

Ken
RCG Plus Member
Latest blog entry: Mini H Quad Project


Thread Tools