Micro3DX - Page 7 - RC Groups
Thread Tools
Mar 25, 2009, 10:54 PM
YardGoat lives with mama
James - I had 2 small problems so far.

1. The back of the canopy that holds the washer did not fit with the rest of the canopy assemble as advertised. I had to trim off the legs of the back piece and glue it to the rest of the assemble with a piece or tri-stock.

2. The trim lines on the plastic canopy seem to be to off. If you follow them, then canopy will be just a tad too short (length wise). Ask me how I know

No real worries, but curious if anyone else has had these problems.
Sign up now
to remove ads between posts
Mar 25, 2009, 10:59 PM
Hodgehound # 3
_Lunchbox_'s Avatar
I had the same problem with the fit up, and also with the canopy being too short.

I do have a question though. Which aileron servo mount do I need to use for the HXT500 servos?
Mar 26, 2009, 12:26 AM
jkarpy's Avatar
Quote:
Originally Posted by Liquidity
James - I had 2 small problems so far.

1. The back of the canopy that holds the washer did not fit with the rest of the canopy assemble as advertised. I had to trim off the legs of the back piece and glue it to the rest of the assemble with a piece or tri-stock.

2. The trim lines on the plastic canopy seem to be to off. If you follow them, then canopy will be just a tad too short (length wise). Ask me how I know

No real worries, but curious if anyone else has had these problems.

Trim the front of the base so the canopy goes further back.

Not sure what you are talking about on the head rest not fitting.
Mar 26, 2009, 12:29 AM
jkarpy's Avatar
Quote:
Originally Posted by rcproptester
I had the same problem with the fit up, and also with the canopy being too short.

I do have a question though. Which aileron servo mount do I need to use for the HXT500 servos?
It's not designed specifically for the HXT500 servo. Your going to have to fit it . How much does that servo weigh?
Mar 26, 2009, 12:36 AM
jkarpy's Avatar

Canopy mounted


Some trimming of the base and headrest are required.
Mar 26, 2009, 05:41 AM
Hodgehound # 3
_Lunchbox_'s Avatar
Here are the specs on the HXT500 servo.
Size : 22.9x11.4x22 mm / 0.9x0.45x0.87 in
Voltage : 3v ~ 6v
Weight: 5g / 0.18oz
Speed : 0.10 sec/60(4.8V)
Torque : 0.8 kg-cm
Working Temp : -30C~60C
Teflon Bushing, 15cm wire, coreless motor
Servo arms & screw included
Mar 26, 2009, 05:44 AM
Hodgehound # 3
_Lunchbox_'s Avatar
Looks to be about the size of a S60 servo. http://www.horizonhobby.com/Products...ProdID=EFLRS60
Mar 26, 2009, 08:10 AM
YardGoat lives with mama
Thanks James. I will do a little trimming tonight.
Mar 26, 2009, 08:52 AM
jkarpy's Avatar
Quote:
Originally Posted by rcproptester
Here are the specs on the HXT500 servo.
Size : 22.9x11.4x22 mm / 0.9x0.45x0.87 in
Voltage : 3v ~ 6v
Weight: 5g / 0.18oz
Speed : 0.10 sec/60(4.8V)
Torque : 0.8 kg-cm
Working Temp : -30C~60C
Teflon Bushing, 15cm wire, coreless motor
Servo arms & screw included
Try the servo mount labeled DSP60. That is for the Spektrum servo which looks like the same servo.
Last edited by jkarpy; Mar 26, 2009 at 08:11 PM.
Mar 26, 2009, 07:04 PM
Hodgehound # 3
_Lunchbox_'s Avatar
Thanks James, I will do that!
Mar 30, 2009, 09:57 AM
jkarpy's Avatar

Video of Micro3DX flying


https://www.rcgroups.com/forums/show...5#post11912519
Last edited by jkarpy; Jan 20, 2010 at 06:51 PM.
Apr 09, 2009, 05:59 AM
Hodgehound # 3
_Lunchbox_'s Avatar
James, I got the 3dx completed. I was planning on using the battery from my micro ssx in it, but it is too long to fit and still close the hatch. It is a PQ 400 mah 2s pack. What battery do you recommend?
Apr 09, 2009, 01:20 PM
It took me 30 years?!?!!!
How 'bout these?

https://fusion-pack.com/productdetai...id=192&cat=112
Apr 09, 2009, 02:07 PM
jkarpy's Avatar
Quote:
Originally Posted by btsai
The largest battery that will fit is 11mm X 53 mm X 33 mm. I recommend spending the extra 5-15 dollars for the thunder power, Vampower or one of the Dualsky batteries. Besides, the Fusion is only 360 ma so you will not get a long flight.

http://thunderpowerrc.com/html/prolites.html


http://www.vampowerpro.com/store/com...2_Cell&pid=144

http://www.2dogrc.com/ecommerce/os/c...nt-p-2174.html

James
Apr 09, 2009, 02:54 PM
It took me 30 years?!?!!!
Another option -- although currently out of stock...

http://www.hobbycity.com/hobbycity/s...0C_Lipoly_Pack

I have several sizes of Rhinos -- 2S and 3S -- some for several months -- and all have performed wonderfully.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Work In Progress.....My New AP Ship MarkJayne Aerial Photography 172 May 11, 2008 12:38 PM
Discussion My new F3P work-in-progress Doug Cronkhite Indoor Pattern/F3P 13 Jan 19, 2008 10:16 PM
Discussion The new Shop! A work in progress..... Joe Bennett Aerial Photography 46 Aug 10, 2006 01:46 AM
2 New Micros (Work in Progress) MPL0527 Scratchbuilt Indoor and Micro Models 7 May 08, 2005 04:11 PM
My new GWS Spitfire - work in progress mattski GWS (Grand Wing Servo) 2 Sep 07, 2003 06:50 PM