Micro3DX - Page 4 - RC Groups
Thread Tools
Dec 10, 2008, 09:35 PM
jkarpy's Avatar
Quote:
Originally Posted by DesmoHead
James,

Any flight videos to hold us over until the kit arrives?

-Eric
I will try and get some good footage over the weekend.
Sign up now
to remove ads between posts
Dec 16, 2008, 11:07 PM
bucket of prop wash
garrcass's Avatar
Jkarpy i just wanted to share this way of puting on eazy conectors it has been the easyest way i have ever found all you need is a pair of miniature flush cuters it works great
Jan 26, 2009, 11:07 PM
Fly it like you stole it..
Tram's Avatar
Any video of this lil' guy yet?


Jeff
www.CommonSenseRC.com
Jan 28, 2009, 12:39 AM
jkarpy's Avatar
Quote:
Originally Posted by Tram
Any video of this lil' guy yet?


Jeff
www.CommonSenseRC.com
I am sending one to Fred Midget soon. He does the best job with video.

James
Jan 28, 2009, 01:56 AM
Fly it like you stole it..
Tram's Avatar
Awesome.. Can't wait to see it fly!
Jan 29, 2009, 10:20 AM
Destructive Tester
jimmy34256's Avatar
Does Graves have these yet??????
Jan 29, 2009, 12:11 PM
jkarpy's Avatar
Quote:
Originally Posted by jimmy34256
Does Graves have these yet??????
Yes they do.
Jan 29, 2009, 05:21 PM
Registered User

Micro 3D


I finished building my micro 3D this week, what a great build. As with all of James kits it went together with out any problems. All the parts fit like a glove and the good new I didn't have any parts left over. The instructions were very clear. follow the steps as he has them in the instruction. I haven't had a chance to fly it, the weather has turned cold with lots of wind (wind is not my friend) You can't go wrong with this kit, I know it will fly as good as it looks.
Spud
Last edited by Spudx; Jan 31, 2009 at 11:04 AM.
Jan 29, 2009, 07:04 PM
Destructive Tester
jimmy34256's Avatar
Quote:
Originally Posted by Spudx
I finished building my micro 3D this week, what a great build. As with all of James kits it went together with out any problems. Al the parts fit like a glove and the good new I didn't have any parts left over. The instructions were very clear. follow the steps as he has them in the instruction. I haven't had a chance to fly it, the weather has turned cold with lots of wind (wind is not my friend) You can't go wrong with this kit, I know it will fly as good as it looks.
Spud
Nice job with the purple ! Come on down to FL !!!!!! You can carry on the Micro 3D....
Jan 30, 2009, 08:22 AM
Registered User
Quote:
Originally Posted by jimmy34256
Nice job with the purple ! Come on down to FL !!!!!! You can carry on the Micro 3D....
Fl sounds really good right now, It is cold and windy here
Jan 31, 2009, 04:06 PM
jkarpy's Avatar
Quote:
Originally Posted by Spudx
Fl sounds really good right now, It is cold and windy here
Today was a perfect day for flying.
Feb 02, 2009, 06:37 PM
Registered User

3d


The wind finely slowed down today and I decided to give it a try. It was one of those days if any thing could go wrong it did. I checked out all of the controls and it appeared everything was OK, so off I went. The plane took of fine and I was able to do a slight amount of trimming (it wanted to go right) got everything aligned and was flying pretty go. Then the unthinkable happened, the dam O ring broke and of course the prop came of. I was in the process of flying all most straight up. It started to fall like a rock but then it leveled out. I was able to turn and fly in to the breeze and landed with no problem. So all in all it was a good first flight. The little guy flies great and is very forgiving considering what happened. I didn't have a spare prop or O ring so was through for the Day. I did discover one thing, the solid purple is hard to see and tell direction so will add some white to the under side of one wing.
Spud
Feb 02, 2009, 07:37 PM
jkarpy's Avatar
Quote:
Originally Posted by Spudx
The wind finely slowed down today and I decided to give it a try. It was one of those days if any thing could go wrong it did. I checked out all of the controls and it appeared everything was OK, so off I went. The plane took of fine and I was able to do a slight amount of trimming (it wanted to go right) got everything aligned and was flying pretty go. Then the unthinkable happened, the dam O ring broke and of course the prop came of. I was in the process of flying all most straight up. It started to fall like a rock but then it leveled out. I was able to turn and fly in to the breeze and landed with no problem. So all in all it was a good first flight. The little guy flies great and is very forgiving considering what happened. I didn't have a spare prop or O ring so was through for the Day. I did discover one thing, the solid purple is hard to see and tell direction so will add some white to the under side of one wing.
Spud
I have had O' rings break but not a fresh one. I wish those motors had a shaft, I hate prop savers.
Feb 03, 2009, 08:27 AM
Registered User

Motor


James. I forgot to mention that the little motor you sent me has plenty of Power. I guess I will have to start working on my 3d skills, your never to old to learn.
Spud
Feb 21, 2009, 06:41 AM
Promoting Model Aviation...
Murocflyer's Avatar
Any new updates to share on the Micro 3DX?

I thought I had decided on what new indoor flier to get (Radical RC Mini Stick) until I ran across this plane.

I'd like to hear some more thoughts if you don't mind. Has Napo ordered one to do a review yet? How about Jeff?

Frank


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Work In Progress.....My New AP Ship MarkJayne Aerial Photography 172 May 11, 2008 12:38 PM
Discussion My new F3P work-in-progress Doug Cronkhite Indoor Pattern/F3P 13 Jan 19, 2008 10:16 PM
Discussion The new Shop! A work in progress..... Joe Bennett Aerial Photography 46 Aug 10, 2006 01:46 AM
2 New Micros (Work in Progress) MPL0527 Scratchbuilt Indoor and Micro Models 7 May 08, 2005 04:11 PM
My new GWS Spitfire - work in progress mattski GWS (Grand Wing Servo) 2 Sep 07, 2003 06:50 PM