Thread Tools
Old Oct 08, 2008, 10:43 AM
carolina-mule is offline
Find More Posts by carolina-mule
Registered User
Help!

special care for the aquacraft atlantic harbor tug boat in salt water


will the materials used in the above mentioned boat be compatable for use in salt and brakish (sp) water? what care should be given to the finish and to the electronics?
also is this a good choice in ready to run tug boats?
Sign up now
to remove ads between posts
Old Oct 08, 2008, 11:15 AM
LtDoc is offline
Find More Posts by LtDoc
Registered User
'C-Mule,
The idea is a pretty simple one, the doing of it isn't quite as simple, though. The idea is to get the salt or 'brak' out/off of the boat. Not owning such a tug, I can't tell you how to do that specifically. The getting it 'off' isn't too bad, wash it with 'clean' water. The getting it 'out' isn't as simple, but is basically the same thing, then drying things out and re-lubricating where needed. That generally means taking things apart, cleaning, then putting it all back together again... correctly.
Not much help, I know, but I'll bet there are a few 'salty-dogs' here that can tell you specifically what to do/not to do.
Have fun.
- 'Doc
Old Oct 08, 2008, 02:18 PM
HoaRC is offline
Find More Posts by HoaRC
Registered User
Yes, it's a good choice. But you can also buy the seaport tugboat and convert it to Futaba RC with a new radio, receiver, ESC, battery, and servo. http://www.rcuniverse.com/forum/m_80...tm.htm#8028272

Running on salt water made all my deck screws rusty and very easy to strip.
Old Oct 08, 2008, 02:54 PM
gpzy is online now
Find More Posts by gpzy
FROM THE MIND OF A MADMAN
gpzy's Avatar
Quote:
Originally Posted by HoaRC
Yes, it's a good choice. But you can also buy the seaport tugboat and convert it to Futaba RC with a new radio, receiver, ESC, battery, and servo.

Running on salt water made all my deck screws rusty and very easy to strip.
Doesnt even come close to answering the question.

Fisherman use a prodeuct called SaltX to spray down there fishing gear, helps get rid of the salt. Rinse well with fresh water and lube everything after running. But I think no matter how hard you try salt water will eventually have its affect on any boat you run in it.
Old Oct 08, 2008, 05:07 PM
mfr02 is offline
Find More Posts by mfr02
Registered User
Replace steel screws with brass or stainless. The electronics should be unaffected as the wet is supposed to stay on the outside. The prop and shaft will need a touch of silicon base grease to repel water, and will benefit from regular servicing. The same applies to the rudder.
Cleaning the outside other than corrodible metal is optional - depends on whether you want it to continue looking like a toy or whether you want character.
If there is anywhere that two dissimilar metals meet, such as shaft/bearing/outer electrolytic corrosion will happen. Again, fresh water to remove the salt and a protective layer of grease. My Revell Corvette did an actual 400 miles before the prop shaft needed changing. Thats based on nearly 100 sailings per year over 5 years on a salt 'n' silt lake 1 mile round.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Atlantic Harbor Tug Capt.Crash Dock Talk 392 Nov 10, 2016 07:48 PM
Midwest "the Harbor Tug" plans for trade helifan Scale Boats 2 Oct 09, 2016 04:55 PM
Question RC Nitro Boat in Salt Water? t00fatt Dock Talk 7 Jun 29, 2006 08:00 PM
Discussion Aquacraft Atlantic Horbar Tug wingnut163 Dock Talk 10 Mar 31, 2006 05:31 PM
Any special care for new li-ion camera battery ? Al P Batteries and Chargers 2 Feb 24, 2003 01:08 PM