Thread Tools
Old Dec 07, 2008, 10:36 AM
nobita is online now
Find More Posts by nobita
Registered User
hello!

I have already requested the necessary material.
thanks Mr. Irving
Sign up now
to remove ads between posts
Old Dec 07, 2008, 11:09 AM
Irving is offline
Find More Posts by Irving
Registered User
Irving's Avatar
Here are my servo setup pics.

And a camera man test run video.
RC Bike 1:12 Ducati Part III (1 min 40 sec)
Old Dec 07, 2008, 11:27 AM
Irving is offline
Find More Posts by Irving
Registered User
Irving's Avatar
Yes, you will have a lot of choices at Tamiya 1/12 scale model.
Just a little fix like rear wheel for Tamiya rear tire.
And don't glue the parts, because you have to re-assemble them.
Screws, piano wire... just no glue.
Old Dec 08, 2008, 10:32 AM
Bod2020 is offline
Find More Posts by Bod2020
Registered User
Does anybody know much about the motors on these Silverlit bikes. I'm pretty sure I'll be getting one for Xmas (heavy hinting) and will no doubt have a go at a few mods. Just wondered whether the motors could be swapped out for uprated ones/or just modded, only seen one picture so far, and couldn't tell whether a Slot/Scalextrix motor might fit. Anybody have any ideas.

Bod
Old Dec 08, 2008, 01:41 PM
CLKSPEED is offline
Find More Posts by CLKSPEED
Registered User
CLKSPEED's Avatar
See if you can see the inside is like putting the traction engine that drives the belt Piņon, thank you.
Old Dec 09, 2008, 06:36 AM
Irving is offline
Find More Posts by Irving
Registered User
Irving's Avatar
Here are the pics about twin motors.
And I tested different batteries, 160mah 7.2V or 300mah 6V.
Original battery is 220mah 4.8V.
Old Dec 09, 2008, 09:25 AM
CLKSPEED is offline
Find More Posts by CLKSPEED
Registered User
CLKSPEED's Avatar
Thank you for the speed champ !!

I think we could win more torque carrying only a Piņon attack to the crown, two pine nuts gives me the impression that the battery wears more and does not have the same speed as a motorcycle slot (I do not know if I explained ..)
Last edited by CLKSPEED; Dec 09, 2008 at 09:31 AM.
Old Dec 09, 2008, 10:02 AM
Bod2020 is offline
Find More Posts by Bod2020
Registered User
Thanks for the photos Irving. What were your experiences with the different batteries, any gains really?

Whats your opinion on swapping out the motors, they look fairly slim line, would something like a slot/scalextrix motor fit? (if it would provide more ooomph).

If I understand CLKSpeed, he is suggesting that removing the two motors and going back to just one good motor, therefore reducing the demand on the batteries, I wonder how this would effect the stablility of the bike?
Old Dec 09, 2008, 11:26 AM
CLKSPEED is offline
Find More Posts by CLKSPEED
Registered User
CLKSPEED's Avatar
Bod2020, by what I see in the photos could be adapted engines mini z boat or change the winding rotor by a more powerful engine as the engine of mini z T2, Z2, MALE AWD ... it could also put bruslhes a set of micro-T.

Irving give us your impressions, thanks!.
Old Dec 09, 2008, 02:53 PM
chrisg333 is offline
Find More Posts by chrisg333
www.kinetic-racing.com
chrisg333's Avatar
Quote:
Originally Posted by CLKSPEED
Thank you for the speed champ !!

I think we could win more torque carrying only a Piņon attack to the crown, two pine nuts gives me the impression that the battery wears more and does not have the same speed as a motorcycle slot (I do not know if I explained ..)
Did he mention Pine Nuts?

Do they grow on Pine Trees?

These on line translation thingies are hesterical.......
Old Dec 09, 2008, 04:54 PM
CLKSPEED is offline
Find More Posts by CLKSPEED
Registered User
CLKSPEED's Avatar
jajajaja is the translator...........are pine nuts
Old Dec 15, 2008, 09:42 AM
Bod2020 is offline
Find More Posts by Bod2020
Registered User
Anymore more mods happening to this bike?

Anybody done anything to the motors? Swapped them out?
Old Dec 16, 2008, 06:34 AM
tungym is offline
Find More Posts by tungym
Registered User
tungym's Avatar
I just bought one. Cannot work out how to take the driver apart from the bike. Anyone help?

The front tire is weight loaded and out of balance. I am trying to balance it. Also there is some resistance on rotating the front tyre. Any chance to change to bearing there?

The motor compartment is pretty small and it seems little chance to upgrade it, unless an overhaul of the gear box as well.

The biker is definitely a master piece. All moving joints and decal are excellent!
Old Dec 19, 2008, 05:07 AM
lalain is offline
Find More Posts by lalain
Registered User
I have 3 Silverlit, including the 2 I have modified:
The first is easy to do:

The second is harder:



The motor is Atomic T2:

The board come from MR2 Mini-Z with optional fets 4562:


With 2 lipos 300mA, the speed is good !
Old Dec 19, 2008, 09:45 AM
CLKSPEED is offline
Find More Posts by CLKSPEED
Registered User
CLKSPEED's Avatar
Lalain Good job, it seems the system of jet 1 / 5.

When you put a video in action.


GREETINGS
CLKSPEED


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
1/3 scale Tyco r/c motorcycle! Kmot Motorcycles 158 Dec 05, 2005 08:31 PM
Am I the Only 1/8th R/C Driver? NitroEvolution Large Scale Cars 17 Mar 17, 2005 06:33 AM
Cheap 25mph R/C motorcycle Setup! sithos Cars - Cars and Parts (FS/W) 2 Dec 04, 2003 08:19 AM
Installing brushless on normal 1:10 R/C car. Any experience? risto Electric Power Cars 3 Mar 20, 2002 12:45 PM
Sceince for kids, sub 1 oz R/C planes aeronutz Scratchbuilt Indoor and Micro Models 3 Dec 17, 2001 05:23 PM