Thread Tools
Sep 13, 2008, 04:21 PM
Registered User
Discussion

help! Blade 400 servo>RX connections


Went to hook up a RX and ran into a snag. While pulling a connection from the RX it popped out and brought the others with it, i.e. disconnected all but one of the wires to the RX.

I cannot locate anywhere a diagram that shows which cable goes to which pins on the AR6100e receiver.

Can anyone help?

Basically there are the following servos on my Blade 400

1. Servo on the RIGHT just behind the main drive shaft

2. Servo on the LEFT just behind the main drive shaft

3. Servo in the nose area which has two connecting rods going from it to the swash plate

4. Connector from the ESC

5. Tail servo (have this one figured out)

On the AR6100e there are the following inputs

AUX1
GEAR
RUDD (I have this one handled>TAIL SERVO)
ELEV
AILE
THRO
BATT

I understand reasonably well Rudder, Aileron, Elevator but that still leaves one left over and no matter what I do my tests (without the HC connected) are not successful.
Sign up now
to remove ads between posts
Sep 13, 2008, 04:43 PM
MrR
MrR
Registered User
From left to right looking at the receiver from the connections on the back:

batt-open
thro-ESC
aile-Lower rear servo
elev-front servo
rudd-tail servo plugs into the gyro, gyro plug goes here.
gear-one yellow wire also from the gyro.
aux1-upper rear servo

Hope that helps you out
Sep 13, 2008, 05:02 PM
Closed Account
http://www.slyster.com/heli/
Sep 13, 2008, 05:36 PM
Google 'Blade 400 bible'
Slyster's Avatar
Yep... this is from the reciever section.. click the link... a great helpful photo

#14- Receiver
"Oops!" I fogot where to plug things in on rx !!!
http://www.helifreak.com/showpost.ph...91&postcount=7
------------------------------------
Jul 10, 2009, 12:48 AM
Sky Soldier
mattxr2i's Avatar
Quote:
Originally Posted by MrR
From left to right looking at the receiver from the connections on the back:

batt-open
thro-ESC
aile-Lower rear servo
elev-front servo
rudd-tail servo plugs into the gyro, gyro plug goes here.
gear-one yellow wire also from the gyro.
aux1-upper rear servo

Hope that helps you out
Maybe a silly question but what is the "batt" connection on the receiver actually used for?
Jul 10, 2009, 01:21 AM
Registered User
Quote:
Originally Posted by mattxr2i
Maybe a silly question but what is the "batt" connection on the receiver actually used for?




Bind plug
Jul 10, 2009, 01:58 AM
Sky Soldier
mattxr2i's Avatar
Quote:
Originally Posted by prop bender
Bind plug
Can it be used to operate anything though?
Jul 11, 2009, 02:25 AM
Registered User
Quote:
Originally Posted by mattxr2i
Can it be used to operate anything though?



No!. Other than to plug in a flightpack battery if you use the reciever in a plank( airplane) Nitro engine powered.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Blade 400 servo and swash settings help variableprollc Mini Helis 5 Nov 05, 2010 10:57 PM
Question Blade 400: servo noise? Jon Craig Mini Helis 11 Jun 19, 2008 10:39 PM
Discussion HELP blade 400 and 6102 waytoofast 3D Electric Heli Flying 0 Mar 16, 2008 04:24 PM
Discussion Blade 400 Servo's Turnell Mini Helis 4 Mar 05, 2008 02:36 PM
Discussion Blade 400 servo rev. switch Bing44 3D Electric Heli Flying 2 Feb 28, 2008 11:35 PM