Thread Tools
Mar 29, 2012, 06:17 PM
Registered User
rimshotcopter's Avatar
Can some please validate this finding for me please? This appears to be the RSSI Pin in the FlySky 6 channel RX.

Here is the Datasheet for the A7105 Chip.

Edited: It appears to me, they are sending the output directly to ground via the resistor. So what I MAY need to do is cut the trace and use a RSSI Buffer

Edited, the named Resistor is a CAP, sorry.
Last edited by rimshotcopter; Mar 30, 2012 at 06:43 PM.
Sign up now
to remove ads between posts
Apr 02, 2012, 08:48 AM
Registered User
Quote:
Originally Posted by rimshotcopter View Post
Can some please validate this finding for me please? This appears to be the RSSI Pin in the FlySky 6 channel RX.

Here is the Datasheet for the A7105 Chip.

Edited: It appears to me, they are sending the output directly to ground via the resistor. So what I MAY need to do is cut the trace and use a RSSI Buffer

Edited, the named Resistor is a CAP, sorry.
Richard this will be of interest to you :
https://www.rcgroups.com/forums/show...1589154&page=2
Apr 02, 2012, 09:09 AM
Registered User
rimshotcopter's Avatar
Quote:
Originally Posted by msev View Post
Richard this will be of interest to you :
https://www.rcgroups.com/forums/show...1589154&page=2
Awe!! Thank you.
Apr 02, 2012, 09:12 AM
Registered User
No problem! I sent you a pm Richard!
Apr 03, 2012, 06:36 AM
Registered User
Quote:
Originally Posted by sharonx View Post
I have orangeRX and RSSI out (self soldiered) to RVOSD. at which value (%) I should excpect fail-safe ? 0% ? 30% ? Thanks.
can you please send me some pics that would be awesome
Apr 03, 2012, 07:03 AM
Registered User
what I was thinking was can't I just tap the pins of my OrangeRx spektrum sattelite port? Is that possible Please respond!
Apr 03, 2012, 07:19 AM
Registered User
Does anyone know the RSSI Pin for the Graupner GR-16 HOTT Reciever?
Apr 10, 2012, 05:01 PM
Registered User
vichito's Avatar

RSSI measurements R149DP


Hello.
I have trouble with the measurements in the RSSI wire R149DP
Tx on 0.20V
Tx off 0.29V
I have taken the measure in the rssi wire, and then verified directly of the pcb in both gives me the same values.
I hope you can understand my poor english.
Thank you
Apr 18, 2012, 04:49 PM
I try to Fly
compa71's Avatar
Quote:
Originally Posted by sharonx View Post
is it the same for OrangeRx R910 Spektrum DSM2 9Ch 2.4Ghz TwinPort Rx?
many thanks for attention
Apr 19, 2012, 07:43 PM
Registered User
sharonx's Avatar
Quote:
Originally Posted by khaled_abobakr View Post
Hi ..

Does any one know where the RSSI pin on the Futaba R6208SB

http://www3.towerhobbies.com/cgi-bin...?&I=LXAVCR&P=V

I did search this forum .. but I didn't find it.

Thanks a lot for your help

Khaled
I too would like to know that
Apr 20, 2012, 01:25 AM
Registered User
galaxy1's Avatar

RX R149DP differences between old and new


I know that there are differences between the old version and new version of the RX R149DP.

I would like to know exactly if if the new version has better receiving and sensitivity.
Apr 26, 2012, 11:16 PM
Registered User
I'm getting 1.2v to .3v with transmitter on and off on a Futaba FP-R148DF using my multimeter. It seems like most people get 2.2v on the top end, not 1.2v. Does that indicate that I did something wrong?
Apr 27, 2012, 03:50 AM
FPV! and nothing else matters.
guy1a's Avatar
Any one had success with soldering the ultra micro small of the rssi pin of the a701* ... The turnigy 9x rx ??
Apr 27, 2012, 05:01 AM
Discovery
ulkar's Avatar
Interested on the turnigy 9x receiver as well, I've seen a few topics about it but never anyone getting it to work properly
Apr 27, 2012, 03:55 PM
Registered User
got 1.2/1000 lawmate.
the covers are off.
vrx on table w/channel switches at left corner, pins facing me w/two blue "tictac" looking components in right corner, and ant. on my right side.

from left to right.
2 pins positioned horizontally(pointing in my direction), not connected to nothing...
3 pairs of soldered pins...
2 pins positioned vertically, not connected to anything...
and lastly 3 pairs of soldered pins.

2 blue "tictac" looking pieces are in the corner.
how are these pins numbered, and does anyone know which pins do i solder my rssi wires to.

much thnx from fpv newb.
looked through out thread,and didnt come across any one with 1.2/1000 lawmate, installing rssi.
thnx in advance.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
For Sale usb cable for futaba/hitec pin (round 6 pins) jaas75 Aircraft - General - Miscellaneous (FS/W) 0 Sep 05, 2008 12:34 AM
Pots for Futaba conquest transmitter hcastell Electric Plane Talk 2 Sep 12, 2001 08:14 AM
Make your own DIN plug for Futaba TX! pullin-gs Electric Plane Talk 0 Sep 06, 2001 08:05 PM
WTB: Hitec 555 rx for Futaba ( Slope Nut Aircraft - Electric - Airplanes (FS/W) 2 Jul 28, 2001 08:54 PM
Programming manual for Futaba 7UAF gwh Electric Plane Talk 3 May 31, 2001 12:43 AM