Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Sep 06, 2008, 11:52 AM
mikeyflight3 is offline
Find More Posts by mikeyflight3
Registered User
Build Log

1st glider build - Sig Riser 100 electric conversion


Have been flying fuel and electric planes for about a year, 3-4 builds. Would like to try an electric glider - chose Sig Riser 100 - LHS had one. Plan on the following gear:

BP Hobbies 2826-6 Motor 730 kv - similar to eflite power 25
CC Phoenix 45
Flight Power 3s 2500 20C
Aeronaut 14x7 folding prop
Futaba 3004's for rudder and elevator
HS 55 for spoilers - one each wing

Planned mods:

New ply firewall on shortened nose for motor mount 3 deg downthrust
2-56 rods for control linkage rudder and elevator
Re-enforce fuse around wing TE
Sig AeroKote Lite covering - have extra

Any thoughts, suggestions, comments would be welcome.
Sign up now
to remove ads between posts
Old Sep 06, 2008, 12:34 PM
robh is offline
Find More Posts by robh
Good, fast or cheap, pick two
robh's Avatar
Hi Mikey... go for it, sounds like it could be fun! Please keep us posted as the build progresses - pics are always good too.

Cheers,

Rob
Old Sep 06, 2008, 01:19 PM
mikeyflight3 is offline
Find More Posts by mikeyflight3
Registered User
Beginning fuse - cut off and angled nose for new firewall
Old Sep 06, 2008, 01:24 PM
Seahag721 is offline
Find More Posts by Seahag721
Registered User
Seahag721's Avatar
Hey Mikey keep us posted on the details of your build. I've been debating on one of two planes the dynaflite butterfly or the sig 100. I'm leaning toward the Sig 100. At any rate here is https://www.rcgroups.com/forums/showthread.php?t=319505 another thread of a sig 100 conversion if you haven't seen it already. :-)
Old Sep 06, 2008, 01:30 PM
Bob Cook is offline
Find More Posts by Bob Cook
The Lone Blue Plaid Flyer
Bob Cook's Avatar
Hay Mike,

I just finished doing this mod a few weeks ago. I added 2 ea 6 inch wing tips to it. I call it the Riser 112. Everything your doing looks good, as far as the planned equipment goes. Here is a shot of my plane. There is a build thread on it here too. Your gonna love it. It flies great.

Bob in Seattle
Old Sep 06, 2008, 04:03 PM
rabidrue1 is offline
Find More Posts by rabidrue1
Blueplaidcanard flyer
Mine uses an E flight 15 motor,with a 12x7 apc. With the motor you have expect 85+ deg climbs.You might want to put 3 deg right and about 5 deg down on that for the thrust lines.The power system you have sounds awsome,but do make sure the wing is flat as per plan so no surprises come at you.On the fuse put a doubler of 1/8 light ply from the cut outs left from the kit on the inside of the fuse behind the former at the back of the wing,even if you use the bolt on wing the aft dowel holes are a weak point.While you are stiffening things up,add some corner gussets to the stab,don't worry the motor and battery will offset the weight.To cool the works use a plastic spoon scoop on the battery hatch and remove the covering from the last lightening hole in the fuse bottom.scottie
Old Sep 06, 2008, 04:44 PM
mikeyflight3 is offline
Find More Posts by mikeyflight3
Registered User
Thanks for the advice.

Some more done - fuse glued, used 1/8 sq and thin ca to re-enforce side to bottom joints - not much weight but more strength and stiffening.

New firewall epoxied in.
Old Sep 07, 2008, 08:17 AM
rabidrue1 is offline
Find More Posts by rabidrue1
Blueplaidcanard flyer
Try what I did,use the left over fuse side and bottom pieces and make a cowl for the motor.I used 1/4sq balsa in the corners so I could round it to a 1 3/4" spinner,the cowl on mine is held on with a 1" wide strip of the fuse covering so I can peel it off if needed.
Old Sep 07, 2008, 10:10 AM
Seahag721 is offline
Find More Posts by Seahag721
Registered User
Seahag721's Avatar
Hey Mikey, I noticed your motor mount seems flush with the firewall, are you using spacers to get your right & down thrust angles or did you cut the fuse to the proper angles. Any advice on which way is better? Your pics are great, so please keep'em coming
Old Sep 07, 2008, 11:21 AM
mikeyflight3 is offline
Find More Posts by mikeyflight3
Registered User
Installed the firewall with 4 deg downthrust, no right but will use washers if necessary.
Old Sep 11, 2008, 10:40 PM
mikeyflight3 is offline
Find More Posts by mikeyflight3
Registered User
Some more work:

made hatch for battery compartment and hatch/cowl combo for esc compartment. Rough shaping until spinner and prop arrive tomorrow.
Old Sep 11, 2008, 10:48 PM
Bob Cook is offline
Find More Posts by Bob Cook
The Lone Blue Plaid Flyer
Bob Cook's Avatar
Looks very nice. Keep on gluing !!!

Bob in Seattle
Old Sep 12, 2008, 05:43 AM
rabidrue1 is offline
Find More Posts by rabidrue1
Blueplaidcanard flyer
Nice work on the hatch/cowl,should look real fine when it's shaved down to the spinner contour.
Old Sep 13, 2008, 01:12 PM
rud-elev is offline
Find More Posts by rud-elev
Registered User
I gather your motor choice doesn't have a reversible prop shaft to allow direct bolting to the inside of a firewall?

R/E
Old Sep 13, 2008, 06:29 PM
Bob Cook is offline
Find More Posts by Bob Cook
The Lone Blue Plaid Flyer
Bob Cook's Avatar
Hi R/E,

I thought that too, but maybe he did that for CG ???

Bob in Seattle


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log Sig Riser 100" Build RC-JG Thermal 109 Feb 13, 2016 11:26 AM
Sig Riser 100 chris dodge Electric Sailplanes 11 Feb 04, 2015 05:56 AM
Build Log Sig Riser 100 build jwhitacre Sailplane Talk 18 Jul 27, 2008 06:40 PM
Sig Riser 100 electric conversion John Gallagher Electric Sailplanes 9 Apr 08, 2004 12:17 AM
Sig Riser 100 NIB soar-iowa Aircraft - Electric - Airplanes (FS/W) 0 Feb 12, 2002 10:09 AM