Thread Tools
Old May 03, 2012, 07:47 PM
tow is offline
tow
Find More Posts by tow
tow
Registered User
tow's Avatar

Pins on MC-24


Need help with the pin-location on MC-24, preferrably from left to right.. I want to install a TU-module but now I`m completly lost.
Thanks for any help..........
Sign up now
to remove ads between posts
Old May 04, 2012, 03:45 AM
robertspil is offline
Find More Posts by robertspil
Registered User
The first solution is extremely simple:
A module TU2 is delivered with a short cable, same connectors as MC24, same cable as the connection from MC24 main board to FM module
You connect one cable from main board to Jeti TU and the second cable from TU to FM .
A picture of the cable:
http://www.rc-easy.com/shop/product_...s-TU2--15.html

If you take out the FM module, and look at the back side there are 5 female connectors
- antenna ( this is the connector near the corner)
-ground
-+ from the battery
+ 6V (needed for the FM module)
PPM signal
There is some info on http://users.belgacom.net/TX2TX/tx2t...h/tx2txgb5.htm

I hope this can help
Old May 04, 2012, 05:05 AM
tow is offline
tow
Find More Posts by tow
tow
Registered User
tow's Avatar
Thank You. Very helpful. You see the problem is I don`t have the cable in question but I`ll try to make it work.
Regards
Old Jul 20, 2012, 09:56 AM
xsubsailor is offline
Find More Posts by xsubsailor
Pants on the ground
xsubsailor's Avatar
subscribed
Old Aug 20, 2012, 04:55 PM
Ripon is offline
Find More Posts by Ripon
Registered User
Trying to get my SAT Rx to bind but I can't get it to show on the Jeti box. Anybody got a simple step by step guide to help me out?
Thanks, John
Old Aug 20, 2012, 06:20 PM
wildpalms is offline
Find More Posts by wildpalms
Professional idiot
What is the Jetibox plugged into?

If using the Jetibox on the TX and the receiver is in clone mode then it won't communicate.

Dave
Old Sep 06, 2012, 11:56 AM
Esprit Model is online now
Find More Posts by Esprit Model
espritmodel.com
We made couple interesting videos. Jeti is proving to be excellent system.

Zb/Esprit Model

Jeti Profi Box with Mezon 130 ESC, Neu 700-3D Motor and Henseleit TDR Helicopter at 148.5mph (240km/h)

Jeti Box Henseleit TDR (2 min 10 sec)


Jeti Profi Box Telemetry Synergy E7.avi (1 min 2 sec)
Site Sponsor
Old Sep 06, 2012, 12:17 PM
Esprit Model is online now
Find More Posts by Esprit Model
espritmodel.com

Jeti Telemetry Variometer w/DC-16 Radio


Another interesting video, Jeti DS-16 transmitter with Variometer.

Zb/Esprit Model

Jeti Telemetry Variometer w/DC-16 Radio (4 min 10 sec)
Site Sponsor
Old Sep 06, 2012, 01:05 PM
Sid3ways is offline
Find More Posts by Sid3ways
DJI Supporter
Sid3ways's Avatar
Quote:
Originally Posted by Esprit Model View Post
Another interesting video, Jeti DS-16 transmitter with Variometer.

Zb/Esprit Model
It would be even more interesting if you could sell it to me!!!
Old Sep 09, 2012, 03:37 PM
GordonP is offline
Find More Posts by GordonP
Registered User
GordonP's Avatar
I have recently bought myself a DC-16 transmitter, and I am slowly converting all of my models (mainly slope soarers) from Spektrum to Jeti. I have a number of models with carbon construction, and previously I used one of the dedicated Spektrum "carbon" receivers with three antennae. I located two of them on each side of the nose, and the third on top of the fuselage just behind the wing. I never had any issues with this arrangement. My question is this: the Jeti EX receivers have two aerials, so where would be the best locations for these on a carbon glider?
Old Sep 09, 2012, 05:14 PM
robertspil is offline
Find More Posts by robertspil
Registered User
look at
https://www.rcgroups.com/forums/show...1114168&page=5
For each antenna, put the last 32mm outside the carbon fuselage : this is the most important.

If needed, use a Jeti receiver with long antennas, allowing the two antennas to exit the fuselage after the wing (one antenna on each side)
A nice protection: http://www.stratair.com/Shop/Produkt...aspx?ArtId=656

Robert
Old Sep 10, 2012, 04:41 PM
Esprit Model is online now
Find More Posts by Esprit Model
espritmodel.com
Quote:
Originally Posted by robertspil View Post
look at
https://www.rcgroups.com/forums/show...1114168&page=5
For each antenna, put the last 32mm outside the carbon fuselage : this is the most important.

If needed, use a Jeti receiver with long antennas, allowing the two antennas to exit the fuselage after the wing (one antenna on each side)
A nice protection: http://www.stratair.com/Shop/Produkt...aspx?ArtId=656

Robert
My simple solution.

Zb/Esprit Model
Site Sponsor
Old Sep 10, 2012, 04:43 PM
Esprit Model is online now
Find More Posts by Esprit Model
espritmodel.com
Quote:
Originally Posted by Sid3ways View Post
It would be even more interesting if you could sell it to me!!!
In few weeks you will be, we are almost done. The radio and R7/9/11 are in final stage of testing.

Zb/Esprit Model
Site Sponsor
Old Sep 11, 2012, 03:15 AM
robertspil is offline
Find More Posts by robertspil
Registered User
Your antennas are under the wing.
For slope soaring I fly often with the plane lower than myself . This is why I prefer a position after the wing.
Robert
Old Sep 11, 2012, 05:43 AM
GordonTarling is offline
Find More Posts by GordonTarling
Supersonic Engineering
GordonTarling's Avatar
Quote:
Originally Posted by robertspil View Post
Your antennas are under the wing. Robert
Not only that they are both on the same side of the pylon, so are shielded when that side of the model is away from you.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Polk Hobby 72Mhz or a 2.4ghz system skotman Radios 5 Apr 27, 2007 09:38 AM
Discussion XPS 2,4ghz system and FDR..? merengue Eagle Tree Systems 4 Apr 27, 2007 06:41 AM
Discussion 6EX-2.4GHz system Rox DIY Electronics 4 Apr 10, 2007 10:07 AM
Sold (pics added)ALULA 3 servo, complete setup with 2.4ghz system rcaddition Aircraft - Sailplanes (FS/W) 2 Apr 10, 2007 12:47 AM
Discussion Spektrum DX6 6-channel DSM 2.4Ghz System cpd1343 Dock Talk 38 Feb 23, 2007 06:53 PM