home build - Page 32 - RC Groups
Thread Tools
Apr 14, 2010, 06:06 PM
Registered User
pyrsly's Avatar
I'll have few of this for sale
Sign up now
to remove ads between posts
Apr 14, 2010, 06:12 PM
Don't worry about it!
j.m.'s Avatar
Will these come with pushrods & a v-mount?

Jon
Apr 14, 2010, 06:25 PM
Registered User
pyrsly's Avatar
v-mount - yes, pushrods - maybe. I'm thinking - pull-spring. I'm also planing to supply T blade, CF horns and titanium wing screws .
Apr 14, 2010, 06:27 PM
Don't worry about it!
j.m.'s Avatar
Ooo!

Sounds expensive...

And will pull spring really be stiff enough for the rest of the airframe?

Jon
Apr 14, 2010, 06:33 PM
Registered User
pyrsly's Avatar
time will tell. one piece fuse goes well with pull/pull or pull/spring. Running pushrods inside is to much pain and outside sims funny.
Last edited by pyrsly; Apr 14, 2010 at 07:02 PM.
Apr 14, 2010, 09:01 PM
Steve
I was thinking your wing would go good on one of those fuses.I have to get your other set airborne yet before I jump into another.Dont go out of bussiness
Apr 14, 2010, 09:07 PM
Registered User
pyrsly's Avatar
hwe hwe... I'm not going anywhere
Apr 16, 2010, 12:18 PM
Scott Zastoupil
szastoupil's Avatar
pyrsly,

Is the fuselage in the photos the same that you have posted as plans earlier in this thread? I realize the hatch/nosecone is at least different. (https://www.rcgroups.com/forums/show...&postcount=268)

I wonder if you have experimented with making a fuse and the layup used.

Scott
Apr 16, 2010, 12:41 PM
Registered User
pyrsly's Avatar
Quote:
Originally Posted by szastoupil
pyrsly,

Is the fuselage in the photos the same that you have posted as plans earlier in this thread? I realize the hatch/nosecone is at least different. (https://www.rcgroups.com/forums/show...&postcount=268)

I wonder if you have experimented with making a fuse and the layup used.

Scott
No, fuse is made by Jim from Colorado. You can get one in FS/W section or here with set of wing and tails.
Apr 16, 2010, 06:14 PM
Registered User
pyrsly's Avatar
#2 is ready! I put all My magic in that wing and it turned out very nice. Even with super thin zone airfoils is still mighty stiff. I can't wait to fly it.
Seba
Apr 16, 2010, 09:45 PM
Not landing late ever again
threcixty's Avatar
Looks nice! You sure got those tows flat! Did you do them on the inside and roll them?

Jim
Apr 17, 2010, 04:36 PM
Registered User
pyrsly's Avatar
new clip
facing flaps (5 min 16 sec)
Apr 17, 2010, 04:37 PM
Registered User
pyrsly's Avatar
Quote:
Originally Posted by threcixty
Looks nice! You sure got those tows flat! Did you do them on the inside and roll them?

Jim
Yup!
Apr 17, 2010, 07:38 PM
working to the closest cm
jirvin_4505's Avatar

facing flaps vid


Quote:
Originally Posted by pyrsly
new clip

Is the cloth going on with the residual 3m77 left over from the paper facing.

What paper are you using for the facing?

Thanks for sharing your techniques with video

cheers jeff
Apr 17, 2010, 09:16 PM
Registered User
pyrsly's Avatar
Yes, I use 3m77 and wax paper. I have tons of it, leftovers from sign shop.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Rave Home build whith chainsaw... hamder Large Scale Cars 24 May 01, 2009 06:07 PM
Question Mig 15 home build parabelum Electric Ducted Fan Jet Talk 8 Sep 08, 2004 11:18 AM
home build zagi thingy Taco RC Foamies (Kits) 2 Dec 02, 2003 05:13 PM
home-build helicopter boxed Electric Heli Talk 0 Sep 05, 2001 06:05 AM