Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Nov 16, 2012, 01:20 PM
AndyCross is offline
Find More Posts by AndyCross
Registered User
Hi,

Made an elevator joiner and utilized just one control rod & servo.
Works superb and saves weight and a lot less hassle. Swapped the wheels for 4" black ones. looks a lot nicer.

My only gripe are the spats are a crud/dirt magnet. Any flying off a wet/damp/muddy grass strip results in virtual complete u/c stripdown and clean.

I think this is more of a summer/dry flyer not a winter hack.

Got a nice 16x8 laminate xoar prop to try yet. Powers impressive on 6s with low amps(under 40) and it sounds lovely.
Fettled the dash a little and made a little more period style.

Specs are
pulso 4120-20 470 kv motor
60amp enrgpro sbec +10amp seperate cc bec
6s flightmax zippy 20c lipos
16x8 prop

auw 8lb 9z
wot 1098w @41amps

Standard digital servos.

cofg as per manual , no additional weight needed

Andy
Sign up now
to remove ads between posts
Old Dec 09, 2012, 03:55 PM
wuest3141 is offline
Find More Posts by wuest3141
Registered User
I am planning to put a Power 60 from leadershobby in mine. Should produce about 1900 watts with 6S power on about a 16 x 10" prop. There's a ton of wing area, so should be a nice flier.
Old Dec 09, 2012, 05:06 PM
cmoulder is offline
Find More Posts by cmoulder
Pullin' G's Man
cmoulder's Avatar
1900 watts for 8.5 lbs?!

Should be a blast!
Old Jun 01, 2013, 09:56 AM
datazman is offline
Find More Posts by datazman
Just Plane Crazy
datazman's Avatar

Special note to Peter M


Peter M:

I could not resist your call for a 62CC version conversion build. You know how I like the scale 30's racers!

I started mine this week. Pictured below is what I am going to call a 'teaser' photo of the hatch I cut out. Please excuse the photo quality as I took it with my smart phone.

Power plant will consist of a RimFire 50CC, 12S 5800 MAh Lipos, Castle 160 HV ESC with a 22 inch propeller. Pitch will be between 10 to 12.

Because it is of the larger version I am going to start my own build thread so I do not take over yours so watch for it in the next week or so. I will be going into detail of every aspect of the build with much better quality photos.

Till the next time.
Ta Ta for now.

Paul
Old Jun 03, 2013, 06:55 AM
cmoulder is offline
Find More Posts by cmoulder
Pullin' G's Man
cmoulder's Avatar
Very cool!

Please paste a link here to your thread. Can't wait to watch your progress.

Bob
Old Jul 01, 2013, 08:38 PM
datazman is offline
Find More Posts by datazman
Just Plane Crazy
datazman's Avatar
Hello all:

As promised, my conversion thread:

https://www.rcgroups.com/forums/show...7#post25458085

Paul
Old Jul 08, 2013, 06:15 AM
Peter M is offline
Find More Posts by Peter M
Registered User
Peter M's Avatar

Special Note to Datazman


Great stuff Paul!

I'm only an occasional visitor to this forum nowadays so I was delighted to stumble on your giant sized conversion thread. Good to see there are still interest in the Sparrowhawk.

Good luck with it!

Regards
Peter
Old Jul 11, 2013, 08:49 PM
cmoulder is offline
Find More Posts by cmoulder
Pullin' G's Man
cmoulder's Avatar
Peter, I have yet another kind of landing gear on order from HK and plan to do major surgery on the wing innards, if necessary, to get some decent, reliable undercarriage on this model. I love the way it flies but dread every landing due to the flimsiness of the stock arrangement. The model has never seen anything remotely resembling a hard landing and yet there are constant problems with bending/twisting/scraping/collapsing. I will post details and photos when I finally get around to it, likely this autumn. For now, it is Pattern competition season.

Bob
Old Jul 12, 2013, 08:09 AM
Peter M is offline
Find More Posts by Peter M
Registered User
Peter M's Avatar
Bob,
I look forward to your photos. I've become used to straightening legs and repairing and repainting the trousers but am open to using a better setup.

Good luck with your competition.

Regards
Peter
Old Aug 05, 2013, 10:29 AM
wuest3141 is offline
Find More Posts by wuest3141
Registered User
You said that you were going to use a 4,000 mAh battery pack? I would try to pack twice that volume into the plane.
Old Nov 22, 2013, 01:00 AM
zeus3313 is offline
Find More Posts by zeus3313
Registered User
does anyone know the last clearence price of these from horizon? I am going to pick one up just dont want to over pay.
Old Aug 19, 2014, 03:42 PM
slowgurlflyer is offline
Find More Posts by slowgurlflyer
Registered User
Still have the Sparrow hawk cowl? I known its years later but you might if you do I'm interested.
Old Dec 16, 2014, 06:49 AM
missle is offline
Find More Posts by missle
Registered User
missle's Avatar
So did anyone ever do this conversion with the E-flite Pwr 160 and if so your opinion please? I came across the 71" version at a LHS for $130 so I had to pick it up. Looking to do the conversion with Pwr 160 on 8S
Old Jan 17, 2015, 12:10 AM
missle is offline
Find More Posts by missle
Registered User
missle's Avatar

My Conversion is completed


For anyone interested, here's the link to my conversion https://www.rcgroups.com/forums/show....php?t=2314445 .I'm hoping to maiden her tomorrow
Old Aug 09, 2015, 10:16 AM
Felipe Garcia is offline
Find More Posts by Felipe Garcia
Registered User
Video my sparrohawk

Setup:

Aerodrive SK3 - 6364-245kv
Prop: 18x8
2P 5000 5S 30C
Jeti90

sparrohawk from seagull models (5 min 37 sec)


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Dumas Sparrow Hawk conversion Martin Hunter Scale Kit/Scratch Built 196 Aug 26, 2007 12:50 PM
First flight of the Dumas 30" Sparrow Hawk! Pics and video included Martin Hunter Scale Kit/Scratch Built 59 Mar 23, 2004 11:48 PM
Seagull Models ARF darrenb Fuel Plane Talk 14 Jan 06, 2004 06:56 PM
Sparrow Hawk Conversion? tekochip Parkflyers 1 Dec 26, 2002 12:07 AM