Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Jan 23, 2003, 04:55 AM
Phat Phreddy is offline
Find More Posts by Phat Phreddy
Waiting for the postman

M-IFO one thing I may have forgotten for my build...


Well the problem is that I am on an Island on the Andaman sea coast of Thailand... Lovely place but damn its hard to get even the most basic of modeling supplies...

I was very graciously helped by Andy Marjama of the mini speed wing (I cant say enough good things about this guy... What a trooper, if anyone is looking for a 24 inch wing and truly exceptional assistance consider him) in assembling all my miltiple US purchases, advising me re-entering the hobby, and figuring out all those incedentals that I may need and would have forgotten...

Well my big box arrived with Li-poly's / chargers / a M-IFO / a MSW / servos / Rx's / plugs / cables / etc and I have that kid at Christmas grin...

Going over the M-IFO instructions there are a few references to CA accelerator to be used on all CA joints... Does this do only what it sounds like and can I get away without it ?? Can I carefully build giving it adequate drying time without it ??

If not I guess hoping that anything that is common in the home can make an adequate substitute is too much to ask ???
Last edited by Phat Phreddy; Jan 23, 2003 at 04:58 AM.
Sign up now
to remove ads between posts
Old Jan 23, 2003, 07:44 AM
Gene Bond is offline
Find More Posts by Gene Bond
Crash Master
Gene Bond's Avatar
You can do without the accellerator, but your hands wull get tired

I used accellerator on about 2/3 of the joints while building mine. I switched to thin CA, and didn't need it on many of the joints. Just use a couple coats, instead.
Old Jan 23, 2003, 08:15 AM
Phat Phreddy is offline
Find More Posts by Phat Phreddy
Waiting for the postman
I have thick and thin CA... this may sound dumb but how much acceleration can CA have... Is the fix not instant (I have not built anything in 10 years) it sure seemed damn instant when I stick my fingers together ??

I dont suppose there is any common garden substitute I may pick up in a hardware store is there ??
Old Jan 23, 2003, 10:15 AM
Jim McPherson is offline
Find More Posts by Jim McPherson
Just an average RC'er
Jim McPherson's Avatar
I built my first regular IFO with no accelerator. Just bind the joints togther, then hold them there with pins or fingers and put the thick CA on them. It'll take a couple of minutes to harden, but it's not that bad.

-Jim
Old Jan 23, 2003, 10:24 AM
Nowell York is offline
Find More Posts by Nowell York
Registered User
Nowell York's Avatar
I use thick CA with the accelerator on the mini--I have more important things to do than to watch glue dry.
Old Jan 23, 2003, 11:38 AM
Phat Phreddy is offline
Find More Posts by Phat Phreddy
Waiting for the postman
Well it turns out I need to go up to Bangkok anyway tommorow and will be there for a few days at least... I had hoped to build over the weekend but I will trawl the web to see if I cant find a model supply store and look up some CA accelerator...
Old Jan 23, 2003, 01:09 PM
MKH is offline
MKH
Find More Posts by MKH
MKH
Registered User
Quote:
Originally posted by Nowell York
I have more important things to do than to watch glue dry.

I agree
Old Jan 23, 2003, 05:56 PM
lompocgreg is offline
Find More Posts by lompocgreg
Registered User
baking soda will accomplish the same task and also act as a filler


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Question Oops, I may have messed up my DL50? kilmerrc36 Hand Launch 6 Dec 29, 2006 07:51 PM
Sold maybe u guys may have a use for these.. xrbeast Cars - Cars and Parts (FS/W) 0 Oct 07, 2005 11:41 PM
What kind of power supplie do i have to use for my lithium charger? lttakas Micro Helis 6 Apr 29, 2003 12:08 PM
Where can I have some Battery packs made for my Teddy? mrebman Beginner Training Area (Aircraft-Electric) 5 May 19, 2001 09:56 PM