New Products Flash Sale
Thread Tools
This thread is privately moderated by chrisf testpilot, who may elect to delete unwanted replies.
Old May 22, 2008, 11:45 PM
IPFlyer is offline
Find More Posts by IPFlyer
Registered User
Great effort. Although since it is moving target, one has to wonder if a Wiki would work better?
Sign up now
to remove ads between posts
Old May 23, 2008, 12:12 AM
TheSuper is offline
Find More Posts by TheSuper
I need a nap
TheSuper's Avatar

MAKE THIS POST A "STICKY"


MAKE THIS POST A "STICKY" so it stays at the top of the forum.
Old May 29, 2008, 03:34 AM
dl2gbm is offline
Find More Posts by dl2gbm
Registered User
Quote:
Originally Posted by chrisf testpilot
Let me know if there is anything else you guys would like to see included.
Great Job! Thanks Chris!
Would like to see a screen shot from the mx-24s module...
Frank
Old May 29, 2008, 08:13 PM
chrisf testpilot is offline
Find More Posts by chrisf testpilot
You can call me FANBOY!
Quote:
Originally Posted by dl2gbm
Great Job! Thanks Chris!
Would like to see a screen shot from the mx-24s module...
Frank
As would I!

Hint, hint Jim..
Old May 29, 2008, 08:16 PM
chrisf testpilot is offline
Find More Posts by chrisf testpilot
You can call me FANBOY!
Quote:
Originally Posted by IPFlyer
Great effort. Although since it is moving target, one has to wonder if a Wiki would work better?
I dont really like wikis, partly because I dont care for the format and partly bcause i already have enough web pages to keep up with. I can work in Word whenever I have a spare minute and dont have to worry about being online on uploading it later. With this I am doing something I would have been already. Not to mention I really didnt spend much time on this at all. Work keeps me in good practice doing stuff like this.

And thank you for all of the compliments
Old May 29, 2008, 09:10 PM
altacom is offline
Find More Posts by altacom
Dick Corby
altacom's Avatar
Quote:
Originally Posted by JimDrew
The problem is that you are using a USB hub. If you plug the XDP into a USB port not connected through a hub, it will work fine.
Also I found that XDP did not like my older computer with the 1.1 old style USB ports. My laptop with 2.0 USB worked fine.
Old May 30, 2008, 10:44 AM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
1.1 USB ports do work. I ran the XDP under Windows 95 with an older laptop.
RCG Plus Member
Old May 30, 2008, 07:12 PM
chrisf testpilot is offline
Find More Posts by chrisf testpilot
You can call me FANBOY!
It could be the power output of the USB port and not the version. Have an older Dell that only has one USB port on it. Plugged in a hub and my mouse and ipod trying to charge and it didnt have enough power to run both.
Old Nov 26, 2008, 07:43 PM
vettdvr is offline
Find More Posts by vettdvr
Registered User
Thank you Thank you Thank you for the guide,, exactly what I needed. Jim
Old Dec 29, 2008, 05:10 PM
MrMike is offline
Find More Posts by MrMike
Watcher of the void ...
MrMike's Avatar
Quote:
Originally Posted by chrisf testpilot
Ok guys I wasnt going to post this until I was finished, my transmitter batteries went dead while I was working on it. <snip> I didnt spend a lot of time on it so be gentle...
Has anybody figured out if Chris' guide is affected by the recent XDP firmware upgrade? I'm thinking the new hopping modes ... ? I got all my stuff upgraded to v3.x but have not lit off the latest XDP software yet.
Old Dec 29, 2008, 08:04 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Right now, the XDP software does not support the new hopping modes. The XDP.exe, RxDiag.exe, and Analyzer.exe programs work without any changes. However, the XDP.exe will show you a corrupted EEPROM message when viewing the Tx settings as the hopping mode is there and not recognized as valid.

The TxDiag,exe and Scanner.exe only work in Hopping mode 1 currently.
RCG Plus Member
Old Feb 25, 2009, 06:59 PM
twang is offline
Find More Posts by twang
Registered User
twang's Avatar
Looks like new software is available. It seems that Scanner.exe and XDP.exe now work, TX Diag to come.
Old Feb 25, 2009, 07:33 PM
vettdvr is offline
Find More Posts by vettdvr
Registered User
Quote:
Originally Posted by twang
Looks like new software is available. It seems that Scanner.exe and XDP.exe now work, TX Diag to come.
I assume you just downloaded. I did the download in Nov just after the update. Is this a new version?
Old Feb 26, 2009, 02:22 AM
twang is offline
Find More Posts by twang
Registered User
twang's Avatar
Yep
Old Apr 03, 2009, 08:07 AM
Flep is offline
Find More Posts by Flep
Registered User
Hello,
I guess it might be interesting to update the "unofficial" guide to the last evolution of the software as it is very helpful and a very good complement to the original user's manual. In fact, the user's manual (or let's call it sheet) does not give as much information with the Xdp as does this user's guide. What's more, it appreciated it and learned a lot in the beginning as I had bought a faulty device that had been exchanged by my dealer without any problems. However, before contacting my dealer, I had to be sure that the device had a problem and that there was no configuration problem caused by myself.
Just an idea.
Best regards.
Flep


Thread Tools