Nov 24, 2011, 11:57 AM
Volts>amps
stgdz's Avatar
Quote:
Originally Posted by LeszekJ View Post
No and yes.
MOSFETs take this role sometimes
Lol that's what I figured.


Hopefully Santa will drop off some tp batts this year but all of my setups are xh.

This guy is what I need correct?
http://epbuddy.com/index.php?main_pa...products_id=38

Its not rated to the 30x series though. That shouldn't matter though correct?
Sign up now
to remove ads between posts
Nov 24, 2011, 12:16 PM
Registered User
Quote:
Originally Posted by stgdz View Post
Is there a fuse in these chargers in case the user does something stupid?
There is a 7A fuse on the DC jack input. That's all.

Fred
Nov 26, 2011, 10:19 AM
Registered User

icharger input solar


to junsi
is it possible to input power into an icharger using a solar panel?
Does the icharger require contant voltage/constant current input?
Would an mppt ( max power point tracker) be useable if it is possible as solar input source to icharger?
If answer to the above is 'no' : would it be possible to modify icharger so it acts as mppt and has input plug for solar input?
Nov 26, 2011, 10:54 AM
Proud to eat Kraut ;-)
Julez's Avatar
A mppt would be nice. The charger itself can be set to a minimum input voltage. If that voltage is undershot, the charge current will be reduced automatically, so that the supply voltage hovers around the level that was set. This way, the charger can compensate the fluctuating output of the panel, and will not just stop with a low voltage error. Just make sure, that the panel's maximum voltage does not exceed the chargers specs.
Nov 26, 2011, 01:55 PM
Go Huskies!
I'm looking to get my first real charger, and the iCharger 206B and 208B caught my eye. Right now my packs range from 1S 160 mAh to 3S 1300 mAh, but I want the charger to be somewhat future-proof and be able to handle larger 4S-6S packs I might use in the coming years.

I know the 206B will handle my current packs, but will it be able to handle the larger packs in the future at decent charging rates, or charging two packs at once?
Nov 26, 2011, 02:17 PM
RC Helicopter Pilot
TheWoodCrafter's Avatar
I went shopping for a good LiPo charger about 2 months ago.

I wanted something future proof also.
I wanted to be able to charge up to 6S batteries.
I needed something that would not take an hour at the field to charge.
I use 2700 mAh batteries now but knew I would be going to 5000 mAh batteries.
I wanted to be able to parallel charge multiple packs in a reasonable amount of time.
So I jumped in the deep end and bought a 306B and built a PS.

I don't think I will ever need another charger.
Last edited by TheWoodCrafter; Nov 26, 2011 at 05:25 PM.
Nov 26, 2011, 03:14 PM
Volts>amps
stgdz's Avatar
The 30x series is not that much more for what you get. I have thought about adding a 29xhalf series with my 306 but the 306 is about twenty bucks more, well worth it fir what you get.
Nov 27, 2011, 09:17 PM
Registered User
Hello Junsi -- that is the correct address. Thank you for getting in touch and I hope to be charging again ASAP.
Thanks for your patience all other readers.
Nov 28, 2011, 09:54 AM
Southern Pride
everydayflyer's Avatar
Perhaps a better means of contac

https://www.rcgroups.com/forums/member.php?u=143941
Nov 28, 2011, 01:18 PM
Registered User
Thank you very much Charles. I struggled to find that contact. I somehow just miss these things when scanning the page. This will prove just ideal.
Apologies again.
Nov 28, 2011, 09:39 PM
Volts>amps
stgdz's Avatar
For a forming charge on a 4000 may nicad I charge at a quarter c, so its 1.0a.

Is there anything else I have to do when doing a first charge on a nicad?
Nov 28, 2011, 11:40 PM
Registered User

balance without charging


Charger Icharger208 +. There is no charge-balancing mode?
Nov 29, 2011, 01:51 PM
Old gasbag glider guy...
Stan Hinman's Avatar
Quote:
Originally Posted by TheWoodCrafter View Post
I went shopping for a good LiPo charger about 2 months ago.

I wanted something future proof also.
I wanted to be able to charge up to 6S batteries.
I needed something that would not take an hour at the field to charge.
I use 2700 mAh batteries now but knew I would be going to 5000 mAh batteries.
I wanted to be able to parallel charge multiple packs in a reasonable amount of time.
So I jumped in the deep end and bought a 306B and built a PS.

I don't think I will ever need another charger.
Same position I was in several months ago, and ended up with the 306B and this 12/24v selectable power supply.
I even have the same case from Harbor Freight. I'm very pleased with this setup.

Stan
Last edited by Stan Hinman; Nov 29, 2011 at 01:53 PM. Reason: clarification
Nov 29, 2011, 01:58 PM
RC Helicopter Pilot
TheWoodCrafter's Avatar
Quote:
Originally Posted by Stan Hinman View Post
Same position I was in several months ago, and ended up with the 306B and this 12/24v selectable power supply.
I even have the same case from Harbor Freight. I'm very pleased with this setup.

Stan
Funny how great minds think alike...

Got any pictures?
Nov 29, 2011, 02:05 PM
Old gasbag glider guy...
Stan Hinman's Avatar
Quote:
Originally Posted by TheWoodCrafter View Post
Funny how great minds think alike...

Got any pictures?
Actually, no. But I can fix that when I get home tonight...

Stan


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Best charger/discharger $ can buy namancio Batteries and Chargers 30 Jan 31, 2010 02:52 PM
Power Pacer Battery charger/discharger ACE_McCOOL Batteries and Chargers 4 Oct 22, 2002 12:39 PM
NIB Hitec CG-325 Charger/Discharger/Cycler for 4-9 cells - $39! Jason M Aircraft - Electric - Airplanes (FS/W) 0 Oct 03, 2002 03:29 AM
WTB Good charger/discharger 10 + cells WickedFunRC Aircraft - Electric - Airplanes (FS/W) 0 Sep 05, 2002 08:55 PM