iCharger 1010B+, 106B+, 208B, 206B, 306B and 3010B - Page 149 - RC Groups
Shop our Airplanes Products Drone Products Sales
Thread Tools
Nov 11, 2008, 11:06 AM
Registered User
Is it possible to use the TP board with a 106b+ to charge 2 x 6s lipos in parallel using the 6s and 7s ports such as how write2dgray described with 3s?
Sign up now
to remove ads between posts
Nov 11, 2008, 05:48 PM
badger-b's Avatar


Originally Posted by synisterphx
Is it possible to use the TP board with a 106b+ to charge 2 x 6s lipos in parallel using the 6s and 7s ports such as how write2dgray described with 3s?
Yes. The charger will still only see the resultant pack as 1 x 6s battery, albeit of twice the capacity.
Nov 14, 2008, 03:04 AM
iCharger 106B user
Friend of mine asked me i he can balance charge NiMH batteries with iCharger? Do nimh need to be balanced? I'm talking about classic AAA (AA) and SC / 2/3A
Nov 14, 2008, 04:29 AM
CamLight Systems
All packs perform better if the cells are all at the same state of charge/discharge. With NiMH (and NiCd) packs, a problem can occur during discharge when the cells are unbalanced and the discharge is deep. If one cell drops below 0V before the overall pack voltage drops to the cutoff point, that cell can have its polarity reversed and be damaged.

While Ni packs are not balanced the same way as Li packs are (with taps) you can balance the cells with a long, slow charge to about 125%-150% of the cell's capacity. The slow charge (0.1C or slower) prevents the cells that are topped off first from overheating as they continue to charge. The long charge makes sure that all of the cells have a chance to fully charge. Once this is done, the pack is balanced. I recommend doing it every month or two for all NiMH and NiCd packs.

To support this, the iCharger has a "Forming Charge" mode. It does a 1C charge to a certain point and then slows down until the charge reaches 125% of the cell's capacity. This will balance the pack.

Nov 14, 2008, 04:49 AM
iCharger 106B user
Thank you
So i could try it with my AA NiMH from my camera and radio (have no icharger here, but hope i can adjust forming charge for AA, coz i can't charge those with 1C)
Nov 14, 2008, 05:04 AM
CamLight Systems
Yes, you can adjust the current the iCharger uses for the Forming Mode, but only after the charge starts.
So it will work for those AA cells, as long as you have a holder for the cells to use during charging.

Otherwise, the iCharger uses the capacity setting you entered in to calculate the 1C initial charging rate. If you tried to trick out the iCharger by entering in a lower capacity to force a lower charge current, then you'd mess up the calculations the iCharger makes to bring the pack to a 125% charge.

Nov 14, 2008, 05:40 AM
iCharger 106B user
I bought some holders (here ), so i'm gonna build something universal.
Hope 1C will not damage AA nimh for that few secs, until i adjust the amps.
Nov 14, 2008, 05:49 AM
CamLight Systems
No worries about any damage. A too-high charge rate will only damage the cell near the end of the charge when it can cause the cell to overheat (unless absolutely ridiculous).

Give David at ProgressiveRC a holler for the iCharger (http://www.progressiverc.com/. He has them in stock and got one to me VERY fast.

Nov 14, 2008, 06:04 AM
iCharger 106B user
So should i change 1C current right after starting or not? Just wait until iCharger drop it to 0.1C automatically?
Holler for the iCharger?
Nov 14, 2008, 06:23 AM
CamLight Systems
Try leaving the iCharger at its own settings for the first charge. But, monitor the cells carefully and if they start to overheat (get too warm to hold for long periods comfortably), stop the charge, let them sit until cool, and then try charging again but try lowering the current, after the charge starts, to 0.5C. I suspect that you'll be OK with the iCharger's 1C selection though.

Sorry...was saying to contact David, i.e., give him a yell or "holler", at ProgressiveRC for the charger.

Nov 14, 2008, 06:26 AM
iCharger 106B user
i have enabled temp probe + will be watching the batteries, too
Still can't understand what you were trying to say? or it wasn't for me?
Nov 14, 2008, 06:37 AM
CamLight Systems
When I said to "give David a holler for the charger" I was saying "contact David about buying a charger". I'm not sure where you're located but "giving someone a holler" is an American slang phrase for calling them or contacting them in one way or another. But I just noticed that your tag is "iCharger 106B user" so you've probably already bought one.

Great idea about the temp probe, forgot about that. Be sure to very firmly connect it to the cell and cover it with a couple layers of tape or a blob of modeling clay to make sure that area doesn't cool down in the air before the heat reaches the probe.

Nov 14, 2008, 07:08 AM
iCharger 106B user
Oh.. i see, i'm from Slovakia

I'm puting temp probe over the battery so it has proper temp contact (battery weight make the probe stick to the battery case)
Nov 14, 2008, 08:09 AM
Registered User
ukpaul's Avatar
It says on each of his posts where he is from, & if you click on his name, then click on location, it shows a map of where that is in the world.
Nov 14, 2008, 08:14 AM
iCharger 106B user
knowing location don't make you know the local slang
if it is what you wanted to say

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Best charger/discharger $ can buy namancio Batteries and Chargers 30 Jan 31, 2010 03:52 PM
Power Pacer Battery charger/discharger ACE_McCOOL Batteries and Chargers 4 Oct 22, 2002 01:39 PM
NIB Hitec CG-325 Charger/Discharger/Cycler for 4-9 cells - $39! Jason M Aircraft - Electric - Airplanes (FS/W) 0 Oct 03, 2002 04:29 AM
WTB Good charger/discharger 10 + cells WickedFunRC Aircraft - Electric - Airplanes (FS/W) 0 Sep 05, 2002 09:55 PM