Thread Tools
Old Mar 30, 2009, 04:37 PM
alexsosnovski is offline
Find More Posts by alexsosnovski
Registered User
It was a good lesson for me not to hurry. Such lessons should better be learnt on cheap and easy to repair planes than on something bigger and more expensive.
Sign up now
to remove ads between posts
Old Mar 30, 2009, 05:26 PM
adbradley is offline
Find More Posts by adbradley
Registered User
adbradley's Avatar
Yes this is very true!
Old Mar 31, 2009, 01:14 AM
aqkhana2002 is offline
Find More Posts by aqkhana2002
Registered User
Thank you Pat! for F15 , so are we going to make it of 3mm? or 6mm?
Old Mar 31, 2009, 09:04 AM
adbradley is offline
Find More Posts by adbradley
Registered User
adbradley's Avatar
its designed for 3mm
Old Mar 31, 2009, 09:37 PM
martys is offline
Find More Posts by martys
Check your six
martys's Avatar

F15


Adam, is the center fuse made from 6mm or 3mm? Thanks Marty
Old Mar 31, 2009, 10:12 PM
crxmanpat is offline
Find More Posts by crxmanpat
Foam abuser!
crxmanpat's Avatar
I would use 6mm for the center fuse section. It works great on the F-22 and has been rock solid in a few smash ups.

Pat
Old Apr 01, 2009, 09:17 AM
adbradley is offline
Find More Posts by adbradley
Registered User
adbradley's Avatar
its designed for 3mm, but 6mm would work also, just have to widen the notches
Old Apr 05, 2009, 03:29 PM
JaJaJim is offline
Find More Posts by JaJaJim
Registered User
+1

4mm depron, robbe ROXXY 2214/31 outrunner, HYPERION TITAN 10A esc, AR6100 6CH DSM2 and kokam 450MAH 11.1V accu

weight +- 145g, near 2.1 trust/weight
Last edited by JaJaJim; Apr 07, 2009 at 05:00 PM.
Old Apr 05, 2009, 04:10 PM
adbradley is offline
Find More Posts by adbradley
Registered User
adbradley's Avatar
looks great!!!
Old Apr 05, 2009, 05:13 PM
JaJaJim is offline
Find More Posts by JaJaJim
Registered User
thanks a lot for pdf`s !
Old Apr 05, 2009, 08:05 PM
aqkhana2002 is offline
Find More Posts by aqkhana2002
Registered User
guys what about F15 Progress ? is any one start making it????

video for my F22, remmber i am new pilot


20090405072515 (2 min 48 sec)
Last edited by aqkhana2002; Apr 05, 2009 at 11:44 PM.
Old Apr 10, 2009, 06:21 AM
aqkhana2002 is offline
Find More Posts by aqkhana2002
Registered User
Ok Guys, here is F15 Pic, Pat if you think i am some where wrong please let me know. Hope fully i will finish that tomorrow. and will post an update...
Old Apr 10, 2009, 11:27 AM
adbradley is offline
Find More Posts by adbradley
Registered User
adbradley's Avatar
aqkhana, that looks great! how did all of the parts fit? did you find any errors?

Thanx

Adam
Old Apr 11, 2009, 08:43 AM
aqkhana2002 is offline
Find More Posts by aqkhana2002
Registered User
Quote:
Originally Posted by adbradley
aqkhana, that looks great! how did all of the parts fit? did you find any errors?

Thanx

Adam

yes adam , all parts were ok! i will post more pic after 2hr

cheers
Old Apr 11, 2009, 02:41 PM
Janusz Jawien is offline
Find More Posts by Janusz Jawien
Registered User
Janusz Jawien's Avatar
Hi Guys,
I just maiden my F15! Flew great, no trim necessary, I just had to dial 40% expo to ailerons, somehow it is much more sensitive to roll then F22.
All the guts were transfered from my F22, no change.
The batery has to be att. up front of airscoop on the vertical part of fuse to get proper CG.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold 3mm White Depron 18 sheets Twinkletoze Aircraft - General - Miscellaneous (FS/W) 1 Sep 06, 2007 10:57 PM
Built up 3mm depron aerobatic/3D??? bcripe1 Foamies (Kits) 4 Sep 03, 2003 09:00 PM
3mm depron CAP MGoddard Foamies (Kits) 3 Sep 01, 2003 08:36 PM
Slice BlueCore into 3mm Depron localbuyer Foamies (Kits) 1 Jul 08, 2003 11:28 PM
For Sale Fs 3mm Depron Sheets CMT1961 Aircraft - Fuel - Airplanes (FS/W) 2 Jan 28, 2003 01:01 PM