Thread Tools
Dec 28, 2007, 08:48 PM
Registered User
Discussion

3D Training Videos


Hello All,

Lets dedicate this thread to a collection of links to training videos, specifically the ones with stick overlays. Once fully populated, this thread will serve as one stop for learning 3D maneuvers.

Lets share our collection of links to 3D learning videos.

Here is a collection of my links:

http://www.privateradio.org/7channels/

How to Lomcevak (4 min 8 sec)


http://www.teamflyingcirkus.com/ (You would need to create an account, and once logged in, go to Media Center-->3D University)

http://www.flyinggiants.com/
http://www.flyinggiants.com/content/groundschool.aspx



AirBorne_AZ
Last edited by AirBorne_AZ; Mar 02, 2011 at 11:06 AM. Reason: 7Channels weblink has changed. Thanks for the update FlopGun!
Sign up now
to remove ads between posts
Dec 29, 2007, 02:11 AM
Registered User
Blender, KE Spin, KE circles, Flat spins (inverted and upright), Harrier, Inverted Harrier, Hover, Rolling Harrier (both ways), High Alpha KE, Snap roll, Slow roll, Waterfall, Tumbling.

You can find the first 3 here https://www.rcgroups.com/forums/showthread.php?t=786514, and the remaining videos here
Last edited by Malves; Feb 01, 2008 at 08:07 AM.
Jan 06, 2008, 08:18 AM
pǝʇɹǝʌuı
Coonak's Avatar
These would have to be my fav instructional vids.
Learnt heaps from em!

Rolling harrier how to with sticks overlay!
Mark Leseberg Instructional Vid

Plane setup with Andrew Jesky is another great vid!
Andrew Jesky Instructional Vid

Andrew Jesky Mixing Instructional

Cheers

Mick
Jan 08, 2008, 01:16 AM
Registered User
earlybird2's Avatar
Great idea.

Ben
Feb 11, 2008, 10:39 AM
Registered User
jonnyjetprop's Avatar
http://www.3dhobbyshop.com/HowToFly3DVids.htm

John
Feb 18, 2008, 10:17 AM
Registered User
Hangar 9's FS1 has quite a few training videos that i like to watch.
Feb 20, 2008, 01:31 PM
Custom CNC machining
jrubenis's Avatar
Ok i am new to 3d and need someone to explain the moves for me. Not how to do them but the names. I know knife edges harrier torque rolls but what are benders and KE benders?? And waterfalls? I have looked on youtube for some vids but dont know which moves are called what Thanks.
Feb 20, 2008, 03:23 PM
Registered User
Quote:
Originally Posted by jrubenis
Ok i am new to 3d and need someone to explain the moves for me. Not how to do them but the names. I know knife edges harrier torque rolls but what are benders and KE benders?? And waterfalls? I have looked on youtube for some vids but dont know which moves are called what Thanks.
The blender is where you come in a dive while rolling and put it into a inverted flat spin. A water fall is where you hover and apply full throttle and do a outside loop and get into a hover again.
Feb 20, 2008, 03:40 PM
Custom CNC machining
jrubenis's Avatar
Thanks. I have found a site which shows pictures and names of the moves. One last thing. It says full down elevor,after the roll and rudder for the blender, is that full down stick (ele up) or actual elevator down (stick up)???

Found all these on WWW.YOUTUBE.COM just do a search for RC TRAINING and it has all the moves, with stick overlay, as done on a simulator.
Last edited by jrubenis; Feb 20, 2008 at 03:47 PM.
Feb 20, 2008, 03:44 PM
Registered User
Quote:
Originally Posted by jrubenis
Thanks. I have found a site which shows pictures and names of the moves. One last thing. It says full down elevor,after the roll and rudder for the blender, is that full down stick (ele up) or actual elevator down (stick up)???
I dont understand. Whats your question. Do you have a sim. to practice on?
Feb 20, 2008, 03:54 PM
Custom CNC machining
jrubenis's Avatar
Yeah i have aerofly, but a broken hand means i cant hold controler properly. I was reading a "walkthough" about some 3d moves and it often says full down/up elevator. I wasnt sure if it mean elevator stick down or up,,OR the elevator physically goes up down as they are opposite. To go up, for ex, stick goes down. elevator goes up..hope thats clearer.
Feb 20, 2008, 03:57 PM
Registered User
Ohhh. It means up/down on the plane. So if it said up, pull down on the stick.
Feb 26, 2008, 02:50 PM
Custom CNC machining
jrubenis's Avatar
http://www.troybuiltmodels.com/AwesomePilot.htm
great site for beginners and experts
Feb 27, 2008, 08:27 PM
Want to Fly, Have to Work
BeerBatter's Avatar
Do you have to be registered to Flying Giants to view the Andrew Jesky videos; access denied for me.
Feb 28, 2008, 12:09 AM
Gas Monkey Vic
Vitter's Avatar
Quote:
Originally Posted by BeerBatter
Do you have to be registered to Flying Giants to view the Andrew Jesky videos; access denied for me.
yes register

Vitter


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Yippee! Online 3D Training Videos mo_3dx Fuel Plane Talk 0 May 28, 2004 04:31 AM
More 3D Parkflyer Videos Tim H. Parkflyers 8 Jun 11, 2003 01:46 AM
3D flying videos? (VHS, not web) Ben74 Sport Planes 0 Jun 06, 2002 01:47 PM