Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Mar 21, 2010, 02:09 AM
stinger0518 is offline
Find More Posts by stinger0518
Registered User
stinger0518's Avatar

question on DT750


i want to buy this for my easy fly looking for almost vertical flight just want max climb rate run shut off motor and glide. What wind should i do and what prop would you recommend for glider applications thanks
Sign up now
to remove ads between posts
Old Mar 21, 2010, 09:17 PM
**neons** is offline
Find More Posts by **neons**
5,200 Led Lighted Bike-Bob P.
**neons**'s Avatar
Hey welcome Stinger, that is great. I am using one of these motors on my glider to do just that. I never had to rewind it at all. I use a 1500mah 11.1 lipo and I climb to 1000feet in not to many seconds and shut down and glide. I setup a 10X 8 folder and she moves. I float around for 20 minutes with no thermals. See her fly here: http://rides.webshots.com/video/3049...29027590gZeAPP

Props to select here:
http://www.hobbycity.com/hobbycity/s...2&v=&sortlist=

Here is another of many planes I fly with this motor. Unwound too
P-40 Warhawk with 11X7 prop
http://rides.webshots.com/video/3065...29027590SnnYHY
Give it a try.
**Neons** Bob
Last edited by **neons**; Mar 21, 2010 at 09:32 PM.
Old Mar 26, 2010, 02:03 PM
SteveC68 is offline
Find More Posts by SteveC68
Oh Yeah!
SteveC68's Avatar
What do you use to clean the remaining "factory applied" epoxy from the stator before you rewind? Would MEK clean it without stripping the enamel off? I can never seem to get the little chunks off near top of each tooth.

Thanks,
Steve
Old Apr 01, 2010, 08:27 AM
jackerbes is offline
Find More Posts by jackerbes
Jack
jackerbes's Avatar
I just found these wonderful motors back in stock somewhere finally, it was at R2Hobbies in Hong Kong:

http://www.r2hobbies.com/eng/proddet...=rcps81529_750

I placed a first time order with them, they were polite, quick to reply to an email, and coherent in English.

I still waiting to burn one up so I can try my hand at rewinding.

I use it on my 48", 27 oz., SpaFFFnutz flying wing with a 4S A123 pack. I'm flying a Great Planes 10 x 4.5 slow fly prop on it and getting the results listed and seen below. If anyone is looking for industrial strength slow fly props these props are really the bee's knees:

http://www.electrifly.com/miscproducts/gpmq6610.html

I'm running them on a prop saver at 200 Watts and over using doubled up Thera-Band tubing retainers and haven't lost a prop yet.

Jack
Last edited by jackerbes; Apr 06, 2010 at 07:45 AM.
Old Apr 04, 2010, 07:00 PM
timocharis is offline
Find More Posts by timocharis
Dave North
timocharis's Avatar

Earthquake!


Manuel, I hear it was a big one. Is everything okay?


Dave
Old Apr 04, 2010, 07:59 PM
Truglodite is offline
Find More Posts by Truglodite
Registered Aircraft Offender
Truglodite's Avatar
Yep, a 6.9! Sure hope he's OK. We're prayin' for ya' man.

Kev
Old Apr 05, 2010, 02:12 AM
NX-687 is offline
Find More Posts by NX-687
Registered User

Jack


Quote:
Originally Posted by jackerbes View Post
I just found these wonderful motors back in stock somewhere finally, it was at R2Hobbies in Hong Kong:

http://www.r2hobbies.com/eng/proddet...=rcps81529_750

I placed a first time order with them, they were polite, quite to reply to an email, and coherent in English.

I still waiting to burn one up so I can try my hand at rewinding.

I use it on my 48", 27 oz., SpaFFFnutz flying wing with a 4S A123 pack. I'm flying a Great Planes 10 x 4.5 slow fly prop on it and getting the results listed and seen below. If anyone is looking for industrial strength slow fly props these props are really the bee's knees:

http://www.electrifly.com/miscproducts/gpmq6610.html

I'm running them on a prop saver at 200 Watts and over using doubled up Thera-Band tubing retainers and haven't lost a prop yet.

Jack
Its impossible to burn a DT,,,, Im using a 4SA123 and a 12x6 prop , If I remember that is 18 A

Best motor out
Old Apr 06, 2010, 01:53 AM
manuel v is offline
Find More Posts by manuel v
Registered User
manuel v's Avatar
Thanks Dave and Kev.
Not problem, We are Fine.
check son work place. empty fortunately.
http://www.youtube.com/watch?v=tJjGlJN9s4A

Being Sunday, we were on the airfield.
at that time was flying my f22. and threw me across the earthquake flying the plane. end dizzy.

in 30 years flying, is just my first flight earthquake.

Manuel V.
Old Apr 06, 2010, 08:57 AM
vintage1 is offline
Find More Posts by vintage1
Registered User
vintage1's Avatar
Phew.

where was the epicentre? Baja?
Old Apr 06, 2010, 11:06 AM
manuel v is offline
Find More Posts by manuel v
Registered User
manuel v's Avatar
Yes. 57km Norteast of Mexicali Baja California Mexico.

Manuel V.
Last edited by manuel v; Apr 06, 2010 at 11:30 AM.
Old Apr 06, 2010, 05:23 PM
timocharis is offline
Find More Posts by timocharis
Dave North
timocharis's Avatar
Great to hear you're okay. And that's funny! Those planes make me dizzy anyway ...


Dave
Old Apr 06, 2010, 09:30 PM
Truglodite is offline
Find More Posts by Truglodite
Registered Aircraft Offender
Truglodite's Avatar
Yikes Manuel, was that your video store? Good to hear you're OK and the store was empty. Sounds like a surreal flying experience btw.

Kev
Old Apr 07, 2010, 02:14 AM
manuel v is offline
Find More Posts by manuel v
Registered User
manuel v's Avatar
Quote:
Originally Posted by Truglodite View Post
Yikes Manuel, was that your video store? Good to hear you're OK and the store was empty. Sounds like a surreal flying experience btw.

Kev
Not Kev. is in the ofice were work my sons Alberto And Pedro.

My Video Store is all ok. my airplanes are all Ok.
My House is ok.

Thanks.

Manuel V.
Old Apr 07, 2010, 11:55 AM
timocharis is offline
Find More Posts by timocharis
Dave North
timocharis's Avatar
That's a heck of a mess, but it's cheering to hear your stuff is all okay. The guys making the video seemed to be in good spirits.


Dave
Old Apr 07, 2010, 04:01 PM
jackerbes is offline
Find More Posts by jackerbes
Jack
jackerbes's Avatar
Truglodite wrote:

"..Also need to make something something big enough for this monster..."

The SpaFFFnutz is a righteous flier for the DAT-750, mine is using a Great Planes Power Flow 10 x 4.5 slow fly prop.

Those props are the best industrial strength SF props on the market and really do this motor justice. The 11 x 8.5 is not a slow fly prop, the other listed there are.

Jack


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
lrk-torquemax diy brushless outrunner kit Ron van Sommeren Power Systems 2 Dec 22, 2011 08:45 AM
For Sale hexTronik 24gram Brushless Outrunner 1700kv tallflyer Aircraft - Electric - Power Systems (FS/W) 3 Jul 10, 2007 10:49 PM
English lrk-torquemax diy brushless outrunner site & mailing list Ron van Sommeren Electric Plane Talk 0 Sep 29, 2001 06:57 PM
E-fly-in&diy brushless outrunner meeting, Sept. 2nd, Winssen/Nijmegen,the Netherlands Ron van Sommeren Electric Flight Events 1 Aug 02, 2001 06:37 AM
diy brushless outrunner/LRK meet & E-fly-in, Sept. 2nd, Nijmegen, the Netherlands Ron van Sommeren Power Systems 0 Aug 02, 2001 06:32 AM