Thread Tools
Old Apr 29, 2010, 08:22 AM
erkki is offline
Find More Posts by erkki
Registered User
What is the correct drive angle for the motor, should it be straight or slightly downwards? Usually glider motors need to be quite much downwards, but how is it with Fox?
Sign up now
to remove ads between posts
Old Apr 29, 2010, 02:20 PM
Bobbyr is offline
Find More Posts by Bobbyr
Good Times
Here are 3 First Person Videos taken from my Windrider Fox as requested Ming

808 camera test on windrider fox (2 min 45 sec)

http://www.youtube.com/watch?v=_Dz8V7-x_Bg
Westcliff Portland Dorset (Take 2) (5 min 27 sec)






Bob
Old Apr 29, 2010, 05:38 PM
Ben D Wing is online now
Find More Posts by Ben D Wing
Registered User
Ben D Wing's Avatar
Quote:
Originally Posted by erkki View Post
What is the correct drive angle for the motor, should it be straight or slightly downwards? Usually glider motors need to be quite much downwards, but how is it with Fox?

The motor angle is already moulded into the fuselage halves. No further adjustment should be necessary.
Old Apr 29, 2010, 09:03 PM
suirendoujin is offline
Find More Posts by suirendoujin
Registered User

Few shots from a fortnight ago.


Shots taken during those prescious moments, when I was able to enjoy some stick time.
The light lift flying capability of this semi scale ship is superb. My Fox is always the first one to fly and test lift at the slope.
Old Apr 29, 2010, 09:18 PM
rcairnut is offline
Find More Posts by rcairnut
"Still Crashing since 1960"
rcairnut's Avatar
Quote:
Originally Posted by suirendoujin View Post
Shots taken during those prescious moments, when I was able to enjoy some stick time.
The light lift flying capability of this semi scale ship is superb. My Fox is always the first one to fly and test lift at the slope.
Nice, what is the AUW of your bird?

nut
Old Apr 29, 2010, 10:06 PM
tushev is offline
Find More Posts by tushev
Registered User
tushev's Avatar

Ming, YOU ROCKS !


Thank you for the on board videos! I was more wander to see some video piloting(FPV) though.
I just receive the my FOX, very fast shipping !!! In first look in side the box I was likef..k EPO, but in closer look my chin almost hit the floor, IT IS VERY HIGH DENSITY, TOUGH AND JUICY REAL EPP ! First time I see something designed and moulded so well, this is precious airframe! I will order more for sure. The carbon reinforcement rods are ready installed in the hole length of the wings plus long joiner carbon tube.
So I will start work on it soon and you guys will see the FOX flying over Gotham City just as same as the Marvell's hero
Ming YOU ROCKS, man!
Thank you,
Georgi
Old Apr 30, 2010, 02:35 AM
erkki is offline
Find More Posts by erkki
Registered User
Quote:
Originally Posted by Ben D Wing View Post
The motor angle is already moulded into the fuselage halves. No further adjustment should be necessary.
Ok, that is almost straight then. Motor will be Dualsky XM400ES with AeroCam 9*5 and 3S1250mAh. Now I need just some building time to get it flying
Old May 01, 2010, 08:04 PM
suirendoujin is offline
Find More Posts by suirendoujin
Registered User
Quote:
Originally Posted by rcairnut View Post
Nice, what is the AUW of your bird?

nut
Its about 450 g. This is with new SANWA/Airtronics 2.4 G 92824 Rx, 141 AL for elevator, 9g servo for rudder and a pair of Sx-0912 for ailerons. 1600 mAh NiMH pack powers the radio.
I used kit supplied glass filled strapping tape only, and did not cover the wing with film or the new stuff. Thats why she came out light. Yeah, the wing bends and twists, but she is a nice lift seeker and tester.
Old May 01, 2010, 08:23 PM
rcairnut is offline
Find More Posts by rcairnut
"Still Crashing since 1960"
rcairnut's Avatar
Quote:
Originally Posted by suirendoujin View Post
Its about 450 g. This is with new SANWA/Airtronics 2.4 G 92824 Rx, 141 AL for elevator, 9g servo for rudder and a pair of Sx-0912 for ailerons. 1600 mAh NiMH pack powers the radio.
I used kit supplied glass filled strapping tape only, and did not cover the wing with film or the new stuff. Thats why she came out light. Yeah, the wing bends and twists, but she is a nice lift seeker and tester.
Thanks for the info, it will be helpful on my build,

nut
Old May 09, 2010, 01:52 AM
garrcass is offline
Find More Posts by garrcass
bucket of prop wash
garrcass's Avatar
any one know of a U.S. company that sells these
Old May 09, 2010, 03:16 AM
Andy2No is offline
Find More Posts by Andy2No
NaN
Andy2No's Avatar
Quote:
Originally Posted by olmod View Post
On Molded surfaces i use one of those prick wheel things to run back and forth and use fast cure gorilla with very good results.
I found those are sold in sewing shops and are called tracing wheels. I bought one yesterday for 50p (under a dollar) in my local sewing and mending shop.
Old May 16, 2010, 02:27 PM
Ming is offline
Find More Posts by Ming
Ming's Avatar
Question.
I don't see many Fox using stock DX21 sticker, should I keep to ship this sticker or I need to change another design?

Ming Lou
Site Sponsor
Old May 16, 2010, 03:10 PM
Ben D Wing is online now
Find More Posts by Ben D Wing
Registered User
Ben D Wing's Avatar
Hi Ming, It's a difficult question to answer as different people have differing requirements, but my opinion would be not to bother as most modellers do their own thing anyway.
Old May 16, 2010, 04:12 PM
trees is offline
Find More Posts by trees
Slope Sauce
trees's Avatar
I rarely use sticks so it wouldn't hurt my feelings if they were not included. I'm sure some people love em though. Maybe you could default to not including them unless people specifically ask for them while ordering.


Thread Tools