Sinking a CF spar into the PZ Spitfire Wing.. Any Suggestions - RC Groups
Thread Tools
May 31, 2007, 12:49 AM
Registered User
brati4's Avatar
Help!

Sinking a CF spar into the PZ Spitfire Wing.. Any Suggestions


Needing to sink a CF spar into the wing. I'm hoping not to mare the finish extensively. So I'm up to creative suggestions.. please chim in.
Sign up now
to remove ads between posts
May 31, 2007, 01:49 AM
diligentia vis celeritas
gunracer's Avatar
i've been thinking about the same thing...thinking of using the spar system in an old ef p-47 wing...i think the dihedral is about the same...i would cut into the foam and run the spar from wing skid to wing skid...seal her up and repaint the entire model's underside aircraft gray...
May 31, 2007, 02:16 AM
Registered User
brati4's Avatar
Good point the left wing folded at the root. I think a spar at the point of your simulated landing gear will cover it but end to end would ensure. Prior to the crash I had to touch up the cowling. The shade I found that matched the cowling is RAF sky grey I believe. Either way the color shade is what ever the Brits used from the factory. It matched perfectly. The wing on the other hand is a different shade, so I guess I could repaint it.

Nice garage ceiling, starting to look like mine. I'm gonna try the Align 430, 3550 Kv in my next project. Whatever that may be. I maidened the P-51 with the six series motor, definately an awesome combo. The sound of the motor is better/different than my Aon. I don't know if its the stock prop or the motor windings. I can't wait to see what the eflite props gonna be like. Thanks for the help on my builds.

If you decide to offload any of your prior projects, pm me. I'd definately be interested in helping to clean out your garage.
May 31, 2007, 08:23 AM
Registered User
There is a thread on the PZ FW190 where the guy did put a spar in the wing. Just do a search it was really simple.
May 31, 2007, 12:06 PM
Registered User
brati4's Avatar
Quote:
Originally Posted by KenP
There is a thread on the PZ FW190 where the guy did put a spar in the wing. Just do a search it was really simple.
Thanks for the info, but the wing from the FW is a laminate shell and can be cut open simply by cutting the tape holding it together and inserting a CF rod or shaft. The Spit's wing is solid foam with a laminate coating. Unfortunately wing mods like the Mustang /FW don't apply here.
May 31, 2007, 02:04 PM
Registered User
Oh ok I have not seen a PZ Spitfire yet and assumed the wings were the same as the P51 and FW.

You could use another trick I have seen used in the jet pusher forum. Use a dremel with a round router bit and the router collar. Set the collar to the depth you want the channel and follow a straight edge. That way you would get a nice straight channel to put the rod in. Join the center of two carbon rods with a bent piece of piano wire.
May 31, 2007, 04:06 PM
diligentia vis celeritas
gunracer's Avatar
nice tip ken...
Jun 01, 2007, 12:01 AM
Registered User
Go to this thread post #13

https://www.rcgroups.com/forums/showthread.php?t=554589

Good luck
Jun 04, 2007, 01:42 AM
diligentia vis celeritas
gunracer's Avatar
here's my cf spar install experiment on a broken wing...no glue used as i just wanted to see what it would like...if i was to do this mod, i would only run the spar from wing skid to wing skid...the inboard ends of the spars would be joined thru an aluminum tube bent to match the wing's dihedral...
Jun 04, 2007, 09:42 AM
Registered User
If you are going to go with a flat spar and want to save a bit of cash go with some 1/32 ply and do the same thing.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Looking into traxxas bandit vxl, any suggestions? Firs hi qual rc car LiveElectric Off-road Cars 11 Jun 22, 2007 01:06 AM
Discussion Getting ready to make a wing, any suggestions? Bohh33 Hand Launch 4 Jan 31, 2007 11:17 AM
Discussion twitchy wing.......any suggestions? randall1959 Flying Wings 31 May 01, 2006 12:53 PM
Cutting Wing Ribs - Any Suggestions? fliir Parkflyers 8 Feb 24, 2002 08:36 PM
broken wing dowel, any suggestions cruzomatic Electric Plane Talk 7 May 20, 2001 01:53 AM