New Products Flash Sale
Thread Tools
Old Feb 25, 2007, 03:49 PM
dbacon is offline
Find More Posts by dbacon
Registered User
dbacon's Avatar
Hey Bullseye000,

I made a set of your ball-link pliers, but for the "stud" side, I drilled a small hole, and made a plastic "rivet" and seated it in the hole. Now the ball that I victomize gets a push from soft plastic on its end.
They are sweet, thanks for the directions.
Sign up now
to remove ads between posts
Old Feb 25, 2007, 08:12 PM
AusGeno is offline
Find More Posts by AusGeno
r/c heli noob
Bullseye, do you find using those ball link pliers on the CX2 has any benefits over just using your fingernails? I understand using pliers on T-Rexes etc where the balljoints are on really tight, but all my CX2 ball-joints pop on and off really easily with my fingernails.
Old Feb 25, 2007, 11:16 PM
CX2GoBoom is offline
Find More Posts by CX2GoBoom
Registered User
Does anyone know a good replacement motor for the CX2 Mine a squealing and I think the one for the bottom rotor is failing. The bottom rotor is harder to turn by hand and it seems that when I spool up the motors that the lower blade spools up much later than the top like it is stuck. I also can tell a trim/proportional adjustment differance in flight. Links would be helpful.
Old Feb 26, 2007, 12:12 AM
Diggs is offline
Find More Posts by Diggs
Not your average DiggsyBear
Diggs's Avatar
http://www.miracle-mart.com/store/in...roducts_id=595
http://www.miracle-mart.com/store/in...roducts_id=596

Expensive, but if you want the best replacement motors, these rock. I would also add some of the replacement brushes to your order. I have a pair of these on the CX2 and my squeal is GONE and it is quieter than the stock CX2 new out of the box. Avoid the Vortex motors, hit or miss. A few people had luck with them, but many did not.

GL
Diggs
Old Feb 26, 2007, 12:30 AM
CX2GoBoom is offline
Find More Posts by CX2GoBoom
Registered User
Hey Diggs thanks for the help is any modification required to mount these on a CX2? Does the CX2 heat sink still fit?
Old Feb 26, 2007, 02:16 AM
Rob Hair is offline
Find More Posts by Rob Hair
Registered User
No modification is required - not even soldering. They just plug right into the 4-in-1. Mounting is the same and the heat sink fits. They are much cooler in every way! See:

https://www.rcgroups.com/forums/showthread.php?t=638388
Old Feb 26, 2007, 07:13 AM
jfail is offline
Find More Posts by jfail
Registered User
jfail's Avatar
I see the motors for the Lama on the Miracle Mart website are motors A and B does it make a difference which goes where in the CX2?
Old Feb 26, 2007, 08:37 AM
Rob Hair is offline
Find More Posts by Rob Hair
Registered User
You need one of each, as the pinions are in different positions just like the BCX/2 motors.
Old Feb 26, 2007, 09:33 AM
bullseye000 is offline
Find More Posts by bullseye000
Registered User
bullseye000's Avatar
Quote:
Originally Posted by AusGeno
Bullseye, do you find using those ball link pliers on the CX2 has any benefits over just using your fingernails? I understand using pliers on T-Rexes etc where the balljoints are on really tight, but all my CX2 ball-joints pop on and off really easily with my fingernails.
I didn't until I used my fingernalis and pulled a ball link off of my swash plate. With parts being a challenge to get locally I tried the pliers and think they work better than a fingernail or screw driver.
Old Feb 26, 2007, 01:31 PM
aeronca is offline
Find More Posts by aeronca
The figure "9" Specialist
aeronca's Avatar
A quick question from a relatively new-to-helis guy: Will the CX2 fly OK outside in a slight breeze (5-mph or less)?

Thanks,

Aeronca
Old Feb 26, 2007, 02:03 PM
Rob Hair is offline
Find More Posts by Rob Hair
Registered User
Fly? Maybe.

Crash? Definitely!
Old Feb 26, 2007, 02:28 PM
RickM is offline
Find More Posts by RickM
Model eAviator
GOOD answer ! !
Old Feb 26, 2007, 04:36 PM
Knight48 is offline
Find More Posts by Knight48
Registered User
Knight48's Avatar
Even though I moved the control rod out a hole for forward motion it still stinks even in the slightest breeze!!
Keep it inside buddy!

Pete
Old Feb 26, 2007, 06:36 PM
avocado flyer is offline
Find More Posts by avocado flyer
grant me the serenity....
avocado flyer's Avatar

cx2 TBE help


the short version is: big crash, new swashplate, new blades( balanced pairs ), new alum. bearing holder(not nesc. I just wanted it), new inner shaft(was definatly bent), new lower hub, new flybar. Blades track a.o.k., flybar and upper blades move as freely as they like, and now im getting the dredded TBE, I've searched forum for cx2 toilet bowl and read 99% of the replies, the only thing I can think of is my loose interpritation of klondikes swashplate leveling tutorial. I've never had this problem before, and then again I've never replaced a swashplate before either: could my poor leveling be culprite for TBE. I know the answer is in this forum somewhere, if someone could point me towards it, it would be much appreciated.
Old Feb 26, 2007, 06:59 PM
RCFlyer55 is offline
Find More Posts by RCFlyer55
Angels without wings
I'm new to Helli's but been flying fixed wings for years. A buddy and myself bought 2 of these CX2s at the WRAM show. His flew hands off out of the box. Mine was a bear. Had to mechanically trim for forward and right flight and the nose kept spinning to the left so I had to go to the 4in1 and turn the trim to the right a bunch. I turned the gyro way down because the tail just jittered, and I like it more sensitive. I'm at an 1/8-1/4 turn from the least setting.


So here is where it sucks. I can pirouette fast to the right but since I had to turn the
4 in1 so much to the right it spins very slow to the left. The only way to get it to spin faster is to turn the gyro all the way down.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion to buy or not to buy the blade cx2 airhead225 Coaxial Helicopters 36 Jul 10, 2009 12:01 AM
Discussion Blade CX2 Tx's - Can they be adapted to fly indoor/park flyers Sirion Electric Plane Talk 11 Apr 19, 2009 08:52 PM
Question How to program my dx7 to fly blade cx2? topforce Coaxial Helicopters 4 Sep 23, 2007 10:13 AM
Discussion How do I use my ICE to charge my batterys for blade CX2??? webejpn01 Electric Heli Talk 2 Jan 26, 2007 02:02 PM
Discussion How to learn to fly inverted with the Blade CP? Crazyrcer Micro Helis 4 Apr 05, 2006 01:59 PM