Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Jul 15, 2006, 11:38 PM
nuv22 is offline
Find More Posts by nuv22
Registered User
Help!

Lama 4 in 1 chip falls off after hard landing!--with pictures


so i had my first hard landing... not a crash because it landed on the skids and i did not brake anything on my lama. and all of the sudden everything was dead no lights no nothing! i inspected the battery and put it on the concrete outslide but while i was taking off the battery i heard something loose in the cockpit when i look it was the power chip that ussually blows in the 4 in 1. i will post pictures in a few minutes. it looks like it wasent even soldered on to the board you will see in the pictures what i am talking about.
Last edited by nuv22; Jul 16, 2006 at 12:08 AM. Reason: pictures
Sign up now
to remove ads between posts
Old Jul 16, 2006, 12:22 AM
nuv22 is offline
Find More Posts by nuv22
Registered User
as you can see in the pictures the solder is not even damaged. i dont get why it fell off there is also no solder residue on the chip. wating for the soldering iron to heat up as i type!
Old Jul 16, 2006, 01:39 AM
nuv22 is offline
Find More Posts by nuv22
Registered User
well after some STEADY HAND soldering i finnaly got all the leads of the chip solder on to the board. now comes the power up test. i will let you guys know how it goes wish me luck !lol
Old Jul 16, 2006, 02:08 AM
109Mechanik is offline
Find More Posts by 109Mechanik
Wie Ein floh!
109Mechanik's Avatar
hopefully you made sure the IC was replaced the correct way round before testing....
Old Jul 16, 2006, 02:18 AM
nuv22 is offline
Find More Posts by nuv22
Registered User
ohh yeah made sure that little circle was down at the bottom right. well have full controlls everything works except for the lower rotors (switched the motor leads on the board and both motors work fine) so it must be that i missed a solder point anyone know which lead controlls the bottom rotor?
Old Jul 16, 2006, 03:14 AM
nuv22 is offline
Find More Posts by nuv22
Registered User
its alive ALIVE!!!!!!!!!!!!! both motors working i used a volt meter and found out which lead was not making contact so little more solder and we have power! i will do a fully asembled flight test tomorrow and give an update.
Old Jul 16, 2006, 04:21 AM
nuv22 is offline
Find More Posts by nuv22
Registered User
well why wait till morning right ! flew around a bit and everything is A ok i might have to do a few changes to trim it out again but overall its working great ! here are some pictures.
Last edited by nuv22; Jul 16, 2006 at 04:23 AM. Reason: pics


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Question Mosfet on Lama 4-in-1 Impulz3 Coaxial Helicopters 6 Feb 24, 2008 09:32 PM
Help! BCX 4 in 1 flashing Green and Red after Crash brocja01 Coaxial Helicopters 4 Oct 16, 2006 11:48 AM
Question Where to buy lama 4 in 1? nuv22 Coaxial Helicopters 1 Jul 26, 2006 12:46 PM
For Sale Brand New Esky Lama 4-in-1 & Tx 35 MHz cp-mike Aircraft - Electric - Helis (FS/W) 0 Jul 13, 2006 02:04 PM
Question 4 in 1 not arming until after several connects to the battery. JKA Coaxial Helicopters 13 Jan 12, 2006 09:47 AM