Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Feb 23, 2006, 09:48 AM
chuckand is offline
Find More Posts by chuckand
Registered User

Het 4w


Quote:
Originally Posted by klique
Or randy at dynamoelectrics.com has them,give him a call i dont think they are on his site yet but he has them.
Ck
I've got 2 of 'em... one had white wires and one has black wires. I haven't tested with either yet (maybe this weekend?), but as I recall one was an earlier rev and the other a later revision. I'll report a side by side....

Chuck (in Aaaala Baaama)
Sign up now
to remove ads between posts
Old Feb 23, 2006, 02:12 PM
PaulVi is offline
Find More Posts by PaulVi
resU deretsigeR
PaulVi's Avatar
I would go with Randy at

http://dynamoelectrics.com/

Or

http://www.warbirds-rc.com/

These guys are great Good price and in my case unbelivable service after the sale..


Both Vendors are top notch Same as CK.
Old Feb 23, 2006, 09:14 PM
TaSaJaRa is offline
Find More Posts by TaSaJaRa
More props are better than One
TaSaJaRa's Avatar
Chuckand ,,,,, Looking good so far... I love my TL 50!!! now I just need to get busy on my Demon....
Old Feb 24, 2006, 08:47 AM
chuckand is offline
Find More Posts by chuckand
Registered User
Quote:
Originally Posted by TaSaJaRa
Chuckand ,,,,, Looking good so far... I love my TL 50!!! now I just need to get busy on my Demon....
Thanks! If all goes well, it'll look a LOT better by Monday! I'll report progress then.....

Chuck (in Aaaala Baaama)
Old Feb 24, 2006, 10:01 PM
Talon713 is offline
Find More Posts by Talon713
Registered User
Just wondering is the CC60 overkill for a motor that can only draw 22amps max? ( i.e. The HET 4wind mentioned earlier, in chuckands initial 50" TL component selection) Hmmm?

Happy FAST Flying!!!
Old Feb 24, 2006, 10:44 PM
klique is offline
Find More Posts by klique
Mum is the word!
Talon we pull 40 amps all day long through these motors their ratings are verry consevative.
Chucks setup pulls 42 amps at 24.5 k rpm on the het 4 wind.
ck
Quote:
Originally Posted by Talon713
Just wondering is the CC60 overkill for a motor that can only draw 22amps max? ( i.e. The HET 4wind mentioned earlier, in chuckands initial 50" TL component selection) Hmmm?

Happy FAST Flying!!!
Old Feb 25, 2006, 07:57 PM
Talon713 is offline
Find More Posts by Talon713
Registered User
ck,

That sounds more like it. I was looking at the specs on the Warbirds R-C site. With those numbers the performance would be pretty lethargic, and the motors would probably last forever. But if your pulling that kind of amps, it must rock!!
BONUS...and the price is right... I may have to try one!

Talon
Old Feb 25, 2006, 08:46 PM
klique is offline
Find More Posts by klique
Mum is the word!

Het 4 W


Talon ,bang for the buck you cant beat them I have a few and have used'm for a while.
I havnt even killed one yet,LoL
They work great in a few differant aplications of 3 s 4 s 6 s ,All depending on your needs.
ck
Old Feb 25, 2006, 09:44 PM
Talon713 is offline
Find More Posts by Talon713
Registered User
ck-
Sounds good, Thanks, I'll definately get one and put it thru it's paces. I've had great luck with Megas. They're hard to beat, but a little spendy. BTW- Is Warbirds the place to get them?

Talon
Old Feb 25, 2006, 09:49 PM
klique is offline
Find More Posts by klique
Mum is the word!
FyI Het's are megas.Shhh dont tell anyone.
Ck
Quote:
Originally Posted by Talon713
ck-
Sounds good, Thanks, I'll definately get one and put it thru it's paces. I've had great luck with Megas. They're hard to beat, but a little spendy. BTW- Is Warbirds the place to get them?

Talon
Old Feb 25, 2006, 09:58 PM
Talon713 is offline
Find More Posts by Talon713
Registered User
Will do , I've bought from Randy before he's a great guy, I'll go Dynamo!

Later-

Talon
Old Feb 26, 2006, 12:11 AM
klique is offline
Find More Posts by klique
Mum is the word!
Yo talon randy is my Bro call him a slacker , dirtbag when you talk to him.
Randy is a pretty alrite dude.
Ck.
Quote:
Originally Posted by Talon713
Will do , I've bought from Randy before he's a great guy, I'll go Dynamo!

Later-

Talon
Old Feb 26, 2006, 04:02 PM
Talon713 is offline
Find More Posts by Talon713
Registered User
Ha!Ha! sure will-

Thanks for the heads-up!

Talon
Old Feb 27, 2006, 08:56 AM
chuckand is offline
Find More Posts by chuckand
Registered User

It's ALIVE (...almost....)


So... as promised, here are some pics following the weekend fray.

No great magic here, but I spent about 2 hours over the weekend getting the 50" TL glassed. Had to fit the motor/electronics late last night for grins and spin it up.

I used 6" wide 'glass, as that was all that was available locally. Chris uses 4" in the video, and it may be a little easier to handle, but the 6" worked great for me. Plenty of time to get it applied before the 3M 90 cranked. 6" width made VERY short work of it as well. I am very pleased with the appearance, the rigidity, and the straightness! I left the wing weighted in the (shimmed) beds for both sides and it is flat as a board! Feels like one too....

Ready for covering.... and flight very soon! I'll pick up covering the next night or two and should have it covered by the weekend. Batts may not be in for the weekend maiden though... Fingers crossed...

Oh... right... FYI, the prop is on backwards in the pics too.... Spun it up. No wind. Flipped the prop, mucho wind.

Chuck (in Aaaala Baaama)
Last edited by chuckand; Feb 27, 2006 at 09:04 AM.
Old Feb 27, 2006, 09:01 AM
skymasteres is offline
Find More Posts by skymasteres
Registered User
skymasteres's Avatar
Dude, your prop is on backwards.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log Ritewing Mini-Demon build (22" mini-wing) chuckand Flying Wings 85 Sep 08, 2009 02:10 AM
Yippee! Ritewing "TL 50" Build pics, Maiden and 3 Videos post #57 Newest TaSaJaRa Flying Wings 56 Mar 01, 2007 12:42 PM
Build Log Ritewing 40" TL Build chuckand Flying Wings 123 Jul 28, 2006 02:58 AM
50% Zagnutz build - Here's hoping! bradm Foamies (Kits) 117 Dec 11, 2004 01:13 AM
GWS EDF 50 - what to build? soundman Scratchbuilt Indoor and Micro Models 10 Jul 02, 2003 09:33 AM