Shop our Airplanes Products Drone Products Sales
Thread Tools
Dec 23, 2005, 06:42 PM
Registered User
Discussion

Sub micro biplane


Three canals proportional, with capacity to fly Outdoor


Plantraco receiver of 300mg
Engine of Bit Car G (turbo)
Prop 2X1 remodelled of one 2,5X1 GWS
Wingspan 12cm reduced in 60% of the Micron Guided Mite
Sign up now
to remove ads between posts
Dec 23, 2005, 06:49 PM
Registered User
Very nice! Looking forward to the flight report.

Where do you get such a small battery? Is it a lipo?
Dec 23, 2005, 06:57 PM
No more nicotine for me!
micro_builder's Avatar
i've never seen a biplane version of the MicroMite, i'll have to give that a try sometime, very cool. nice work

nick
Dec 23, 2005, 07:06 PM
Registered User
That batt is a 20 mah lipo. Im not sure how well it will do with a 6mm motor though. Nice plane!
Dec 23, 2005, 07:15 PM
Registered User
Quote:
Originally Posted by anyoneelse
That batt is a 20 mah lipo. Im not sure how well it will do with a 6mm motor though. Nice plane!

In the reality I will use of 60mA but I go to make experiences with the one of 90mA, 80mA and 60mA
Dec 23, 2005, 07:16 PM
Registered User
Quote:
Originally Posted by micro_builder
i've never seen a biplane version of the MicroMite, i'll have to give that a try sometime, very cool. nice work

nick


Nick.. I love biplanes
Dec 23, 2005, 07:17 PM
Registered User
Quote:
Originally Posted by Tshires
Very nice! Looking forward to the flight report.

Where do you get such a small battery? Is it a lipo?


Yes it is Li-po of 20mA but this seems not to have capacity to support the engine
Dec 26, 2005, 10:14 PM
Registered User
Installation of the actuators that has a average of 40 Ohms
Dec 26, 2005, 10:16 PM
Registered User
And....
Dec 26, 2005, 11:17 PM
Registered User
looks nice
Dec 27, 2005, 12:54 AM
Mr. Innocent's Avatar
Looks like you might need a larger rudder and elevator but we'll see!
Dec 27, 2005, 05:29 AM
Registered User
Quote:
Originally Posted by Mr. Innocent
Looks like you might need a larger rudder and elevator but we'll see!
It will not be necessary therefore will have a high speed and the flow of the prop also is great
Dec 27, 2005, 11:30 AM
Registered User
Isn't the receiver 0.38g? And with those connectors added, it's probably more. But I see two actuators so that leasts me to believe it's the 0.9g receiver. What thickness is that balsa? Looks like she'll need to fly quite quickly to sustain lift.
Last edited by ToJo; Dec 27, 2005 at 11:35 AM.
Dec 27, 2005, 12:53 PM
Registered User
Dave Wulff's Avatar
medeiros,

Very nice. I also like the simple coil winder. Could you share some details such as:

How you connected the calculator to count the turns (mechanical, electronic switch etc.)

The construction and materials of your bobbin (form)

Thanks,
Dave
Dec 27, 2005, 04:03 PM
Registered User
Quote:
Originally Posted by ToJo
Isn't the receiver 0.38g? And with those connectors added, it's probably more. But I see two actuators so that leasts me to believe it's the 0.9g receiver. What thickness is that balsa? Looks like she'll need to fly quite quickly to sustain lift.
Yes, it is the receiver of 0,38g and I go to remove the connectors and to weld direct in the plate... I made one another one of 15 cm of wings and it he keeps the same ratios of the commands, and I believe that he goes to function... if not to function I will increase the surface


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
SUB MICRO PICO BB SERVOS gbagley Aircraft - Electric - Airplanes (FS/W) 0 Sep 06, 2001 10:34 PM
MIA's 12" House FLY Sub-Micro! NEWS!!! Mario Electric Heli Talk 160 Aug 08, 2001 12:39 AM
MIA's 12" House FLY Sub-Micro! NEWS!!! (Part 2) MicroRotors Electric Heli Talk 10 Jul 27, 2001 03:19 PM
Need info on FMA Tetra FM 6Ch Sub Micro RX Cash Traylor Electric Plane Talk 3 May 16, 2001 08:31 PM
JR 151 sub micro servos Keithw Power Systems 4 May 08, 2001 01:04 AM