Thread Tools
Old Dec 17, 2005, 03:40 PM
cristal_4_u is offline
Find More Posts by cristal_4_u
Registered User
Cool

Infrared IR Receiver for Serial Port


Hi There,
My name is Cristal. I created a IR Receiver to work with Serial Port.i got the IR Receiver working. I could see numbers when i press Raw Codes. But when I'm doing the Learn Remote part. I can go up to the place where it ask me to enter the button 1 name. I did enter the Name of the button and hit enter and Then it says "Please press and hold down the '1' button until told to stop." I did Press the button but i get error saying "Stop. Failed to get a consistent initial signal. Please try again. You will probably get better results if you increase the margin of error for this remote." I also tried increasing the Margin but still same error. I don't konw what the problem is. Please help me..

Regards,
Cristal_4_u
Last edited by cristal_4_u; Dec 29, 2005 at 11:09 PM.
Sign up now
to remove ads between posts
Old Dec 18, 2005, 07:05 PM
cristal_4_u is offline
Find More Posts by cristal_4_u
Registered User

Infrared IR Receiver for Serial Port


AnyBody out there to help me out with this problem.?
Old Dec 20, 2005, 09:59 AM
ImaBiggles is offline
Find More Posts by ImaBiggles
Master of 1 point landing
Quote:
Originally Posted by cristal_4_u
Hi There,
My name is Cristal. I created a IR Receiver to work with Serial Port using WinLirc. I followed all the instruction from http://lnx.manoweb.com/lirc/ . Now i got the IR Receiver working. I could see numbers when i press Raw Codes. But when I'm doing the Learn Remote part. I can go up to the place where it ask me to enter the button 1 name. I did enter the Name of the button and hit enter and Then it says "Please press and hold down the '1' button until told to stop." I did Press the button but i get error saying "Stop. Failed to get a consistent initial signal. Please try again. You will probably get better results if you increase the margin of error for this remote." I also tried increasing the Margin but still same error. I don't konw what the problem is. Please help me..

Regards,
Cristal_4_u
The receiver is not filtering the signal, hence the issue. Google 'Girder' (IR Remote control prog) and look in the forums for better designs. Also you can purchase a IR receiver for about $15US.
Old Dec 20, 2005, 02:30 PM
cristal_4_u is offline
Find More Posts by cristal_4_u
Registered User
Quote:
Originally Posted by ImaBiggles
The receiver is not filtering the signal, hence the issue. Google 'Girder' (IR Remote control prog) and look in the forums for better designs. Also you can purchase a IR receiver for about $15US.

Hi Dear. Thank you for replying me. I did look into the program Girder. but it the same thing. its not detecting the remote. I dont know why its not Detecting the Remote.
Old Dec 21, 2005, 09:50 AM
ImaBiggles is offline
Find More Posts by ImaBiggles
Master of 1 point landing
Quote:
Originally Posted by cristal_4_u
Hi Dear. Thank you for replying me. I did look into the program Girder. but it the same thing. its not detecting the remote. I dont know why its not Detecting the Remote.
Its not the program, its the receiver. the simple receiver with a couple of resistors and photodiode does not work too well. Girder forum has links to better plans, also one can be purchased for $15 or so. Good luck.
Old Dec 21, 2005, 11:30 AM
siberia37 is offline
Find More Posts by siberia37
Registered User
Try a different remote- the simple IR circuit works for some remotes but not for the more complex ones. Try an old VCR remote or something.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion C++ code for serial port comm Richard Ingram DIY Electronics 13 Feb 19, 2007 06:46 PM
Help! Serial Port connector for FMS Moerdogg Simulators 8 Oct 16, 2006 12:32 PM
need old serial port TX interface cable for Realflight simulator 1g1yy Simulators 1 Mar 27, 2004 08:38 PM
Need old style serial port cable for Realflight simulator 1g1yy Aircraft - Electric - Airplanes (FS/W) 2 Mar 27, 2004 06:44 PM
Found a 'universal' fix for easyfly/piccofly/aerofly serial port problem abennett Electric Heli Talk 1 Jul 27, 2002 08:34 AM