Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old May 04, 2002, 02:07 AM
SoulShell is offline
Find More Posts by SoulShell
Registered User
SoulShell's Avatar

Speed 280 Ball Bearing Soldering


I have a question about soldering wires to my speed 280 BB motor. On the back there are two loose copper wires. What do I do with these? Also, is it ok to get solder on the posts that are near the terminals? These posts have a spring around them. Those of you who know what the back of a 280BB looks like should know what I am talking about. HELP!!! Thanks.

Nick

P.S. If any of you have a picture you could post that shows me that would be great too.
Sign up now
to remove ads between posts
Old May 04, 2002, 03:04 AM
Jurgen Heilig is offline
Find More Posts by Jurgen Heilig
Registered User
Jurgen Heilig's Avatar
Here you can see everything. Wires, Capacitors and ESC. Jürgen
Old May 04, 2002, 08:12 AM
ifxmnfly is offline
Find More Posts by ifxmnfly
Born in the USA.
ifxmnfly's Avatar

Soldering on the can


Nice piture Jurgen! I zoomed in and adjusted the brightness/contrast so I could see the soldering on the can. Your soldering is a lot tidier than I've been able to get on these cans. What wattage of soldiering iron do you use?

I attached the image in case anyone else wanted to see it too:
Old May 04, 2002, 11:14 AM
Jurgen Heilig is offline
Find More Posts by Jurgen Heilig
Registered User
Jurgen Heilig's Avatar
I use an old ERSA pen type soldering iron - 15W only. Jürgen
Old May 04, 2002, 05:12 PM
SoulShell is offline
Find More Posts by SoulShell
Registered User
SoulShell's Avatar
Thanks a lot. This has helped me out a great deal!
Old May 04, 2002, 07:10 PM
ifxmnfly is offline
Find More Posts by ifxmnfly
Born in the USA.
ifxmnfly's Avatar

15 watt Iron


Yeah! Thanks Jurgen.

Now there is a new tool I need to get. Uh ... could you explain this to my wife?
Old May 04, 2002, 11:53 PM
russ6421 is offline
Find More Posts by russ6421
Registered User
russ6421's Avatar
I have no use for the soldering guns to big, with the pen type you can sit it on the bench and use two hands to solder wires together would be ok for doing packs with a big tip.I have a new gun someplace that has never been used.
Old May 05, 2002, 07:34 PM
I FO nut is offline
Find More Posts by I FO nut
Lazy sob
I FO nut's Avatar

jurgen


So you solder the loose copper wires to the ESC leads and in turn solder both to the motor terminals? Am I getting this right!? I couldn't quite tell from the pic.

Thanks
Old May 06, 2002, 11:33 AM
Jurgen Heilig is offline
Find More Posts by Jurgen Heilig
Registered User
Jurgen Heilig's Avatar
ESC wired, copper wires and capacitors, all soldered to the terminals of the motor. A bit tricky, but with the right tools - no problem. Jürgen


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold Great Planes Speed 380 Ball Bearing with Gearbox Twmaster Aircraft - Electric - Power Systems (FS/W) 2 Jul 08, 2007 12:16 PM
Graupner speed 700 Ball Bearing with speed control stealthy Aircraft - Electric - Airplanes (FS/W) 5 Apr 23, 2005 08:44 PM
FS: 2 Speed 280 motors and ball bearing gear boxes - $20 for both Ben Lanterman Aircraft - Electric - Airplanes (FS/W) 2 Jan 05, 2005 08:00 AM
MJ8043 5:1 Gearbox for SPEED 300, Ball Bearing jim mathis Aircraft - Electric - Airplanes (FS/W) 3 Jun 08, 2004 07:30 AM
MPI dual ball bearing gearbox for speed 400 Steve H. Aircraft - Electric - Airplanes (FS/W) 4 Apr 10, 2002 12:25 PM