Thread Tools
Old Nov 21, 2005, 07:49 AM
pacro is online now
Find More Posts by pacro
TOPDOG
is there any chance that Mr. Ming would be interested in making a smaller version thats more sutible for EDF
Sign up now
to remove ads between posts
Old Nov 21, 2005, 08:56 AM
Ming is offline
Find More Posts by Ming
Ming's Avatar
Dear Rudi

Yes, I lost two engine during the fisrt flight, it will not happen anymore because I change to use a rubber band to hold the engine supporting just like the Easy Pro canopy.
It pre-order on our website: http://www.windrider.com.hk/products/product.cfm?id=9
Equipment I am using is:
1. 4 channels TX
2. 4 channels RX
3. Standard AA size RX battery X 4
4. 5 Mini size Futaba #3107 servos
5. 1 Y-cord servo cable
6. 4 extendtion servo cables
7. Some fiber tape

I spend only 1.5 hours to build this ship.

Ming Lou
Site Sponsor
Old Nov 21, 2005, 09:10 AM
Ming is offline
Find More Posts by Ming
Ming's Avatar
Pacro

I don't know how samller you mean...
1 meter may be too heavy to carry 4 duct of the wingload.
2 meter is too large for the machine.
1.5 meter should be OK to power by GWS 50 EDF I think.
Something I can be sure is 1.8 meter is too big after I check up the shipping cost.

Ming Lou
Site Sponsor
Old Nov 21, 2005, 09:23 AM
Ming is offline
Find More Posts by Ming
Ming's Avatar
Ben

Quote:
where do you land this beautiful bird on your hillside
See this movie:
http://www.windrider.com.hk/image/uvs051120-001.WMV

Ming Lou
Site Sponsor
Old Nov 21, 2005, 06:35 PM
FANMAN is offline
Find More Posts by FANMAN
Always looking UP
FANMAN's Avatar
Ming,

Are those holes in the top of the fuse for batteries? It would be nice to allow for alternate battery locations (inside the fuselage) to set the CG for each builders different setup.
Old Nov 21, 2005, 07:46 PM
pacro is online now
Find More Posts by pacro
TOPDOG
why dont you build something similar to the guys at EDFmodel just make them different and instead of moulded plastic make them from EPS
Old Nov 22, 2005, 12:26 AM
Rudi is offline
Find More Posts by Rudi
Registered User
Rudi's Avatar
Quote:
Originally Posted by Ming
Dear Rudi

Yes, I lost two engine during the fisrt flight, it will not happen anymore because I change to use a rubber band to hold the engine supporting just like the Easy Pro canopy.
It pre-order on our website: http://www.windrider.com.hk/products/product.cfm?id=9
Equipment I am using is:
1. 4 channels TX
2. 4 channels RX
3. Standard AA size RX battery X 4
4. 5 Mini size Futaba #3107 servos
5. 1 Y-cord servo cable
6. 4 extendtion servo cables
7. Some fiber tape

I spend only 1.5 hours to build this ship.

Ming Lou
HI Ming Lou,

thx for your fast reply You guys in H.K. know how to fly a power soarer !!!
Very good movies.

greetings from vienna

Rudi

P.S. I dream of a A380 in (future Lufthansaoutfit)
Old Nov 24, 2005, 04:04 AM
zen4013 is offline
Find More Posts by zen4013
Zen
zen4013's Avatar
Hi Ming...the Airbus looks like a great flyer! (I forgot how HUGE this plane is!)
How about an update on how the manufacturing is going (like, have you made more than one successfully from the mold set?) , and perhaps an ETA on deliveries for the testers?


Zen
Old Nov 24, 2005, 10:20 AM
Ming is offline
Find More Posts by Ming
Ming's Avatar
Fanman

Yes, those holes can fit any size of RX, battery or even camera as you like.
Everyone have difference setup.
The correct C.G is located as the orange spot as attached picture.

Ming Lou
Site Sponsor
Old Nov 24, 2005, 10:27 AM
Ming is offline
Find More Posts by Ming
Ming's Avatar
Dear Parco

This is our first airliner to make.
I like huge size not only 1 to 1.2 meter.

Ming Lou
Site Sponsor
Old Nov 24, 2005, 10:30 AM
Ming is offline
Find More Posts by Ming
Ming's Avatar
Rudi

Thank you very much for your nice decal A-380 picture.
In Hong Kong, we always have good wind, no need to fly a power soarer.

Ming Lou
Site Sponsor
Old Nov 24, 2005, 10:35 AM
Ming is offline
Find More Posts by Ming
Ming's Avatar
Zen

Quote:
Hi Ming...the Airbus looks like a great flyer! (I forgot how HUGE this plane is!)
How about an update on how the manufacturing is going (like, have you made more than one successfully from the mold set?) , and perhaps an ETA on deliveries for the testers?
Zen
Zen

The wingspan of this Airliner is 1.8 meter.
Yes, I still have few set but all of them have to keep for more testing.
I have to send modified shot to test pilot not only the 1 st test shot.
ETA is around 20th of Dec...sorry for the late ship again.

Ming Lou
Site Sponsor
Old Nov 24, 2005, 11:05 AM
zen4013 is offline
Find More Posts by zen4013
Zen
zen4013's Avatar
Thats EXCELLENT news Ming, and thank you for the speedy reply.

I'd like to see some posts on possible motor options for these beautiful jets. I personally will try the first one on 2 pusher motors, in order to keep my costs down. Perhaps 2 speed400's DD? I also have 2 Lil Screamers brushless motors that would do the trick nicely. I'd like to keep the prop size small so the plane stays scale looking in flight.

Zen
Old Nov 24, 2005, 11:15 AM
Ming is offline
Find More Posts by Ming
Ming's Avatar
Zen

GWS 55 EDF can fit the Airliner duct.
I think you need 4 EDF to power this ship.

Ming Lou
Site Sponsor


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log Build & fly thread : WindRider Airliner - Big scale PSS marclr Slope 484 Jul 11, 2013 05:03 AM
For Sale Windrider Airliner - A380 in Qantas livery tyga78 Aircraft - Electric - Jets (FS/W) 0 Dec 10, 2006 07:36 AM
Windrider airliner option Ming Slope 25 Dec 10, 2005 11:31 PM
Windrider airliner option Ming Foamies (Kits) 2 Jul 24, 2005 09:42 AM