Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Apr 28, 2005, 07:40 PM
lvmikede is offline
Find More Posts by lvmikede
Registered User
Question

Bug build off for College Engineering Students... need a little help


Hi Guys

I am putting to gether a leasson for some students here at my school, to introduce them to RC flight, composite materials, and aerodynamic basics. I chose the Bug HLG as the perfect little plane for them to build. I have a few questions though about loadout equipment.

We plan on building about 5 of the bugs and would like to know what equipment, servos, reciver, and batteries that you all have had success with. Cost is a big concern for this project, but radios are not an issue. Any help would be great.


Mike
UMR
Sign up now
to remove ads between posts
Old Apr 28, 2005, 07:53 PM
DlgHucker is offline
Find More Posts by DlgHucker
Registered User
Lots of good Bug info here: http://groups.yahoo.com/group/BugHLG/
Old Apr 28, 2005, 08:22 PM
lvmikede is offline
Find More Posts by lvmikede
Registered User
Thankyou
Old Apr 29, 2005, 12:55 AM
John Gallagher is offline
Find More Posts by John Gallagher
Registered User
John Gallagher's Avatar
Most people are using a GWS GWR-4P receiver because it's about the lightest you can get but it can have interference problems. A FMA M5 receiver is a bit pricy but gets better reception. I used Hitec HS-50 servos, but there are some new small servos that would work. 8 or 9 ounce torque servos are fine. Use the plans radio gear placement as just a suggestion. Once the glider is built place the gear where necessary to balance. My tail was a bit heavy (+ tail) so I wound up putting all radio gear forward of the wing.
Old Apr 29, 2005, 02:36 PM
lvmikede is offline
Find More Posts by lvmikede
Registered User
Well, Guys thanks alot for all the help. With a little funding I hope to get this little project off the ground. With the GWS recivers is their a way to reduce the interference?


Mike
Old Apr 29, 2005, 03:20 PM
stjobs is offline
Find More Posts by stjobs
Registered User
Keep the antenna stretched out and at full length. Route it away from carbon. You should be fine especially on a small model - the visual range is not that large anyway. GWS Rxs have worked fine on everything from a Shockflyer to a Pocket F/A-18 Falcon.... I've had the Falcon specked out at almost half a mile away with no problems.
Old Apr 29, 2005, 08:21 PM
lvmikede is offline
Find More Posts by lvmikede
Registered User
My group has a backing from Hitec! YEAH! We are able to get the servos at cost. Now to see if i can push them to get recivers....
Old Apr 29, 2005, 08:27 PM
John Gallagher is offline
Find More Posts by John Gallagher
Registered User
John Gallagher's Avatar
Quote:
Originally Posted by stjobs
Keep the antenna stretched out and at full length. Route it away from carbon. You should be fine especially on a small model - the visual range is not that large anyway. GWS Rxs have worked fine on everything from a Shockflyer to a Pocket F/A-18 Falcon.... I've had the Falcon specked out at almost half a mile away with no problems.
I'm fine with the GWS at my home field, but went to a hand launch contest last year and even though noone was on my channel, with about ten people flying, I lost all control 45 feet from the Bug. It actually nosed under and landed inverted without damage.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Need a little help... Beginner almost lifting off.... HELP mdavenport Micro Helis 33 Jan 19, 2007 02:16 PM
Need a little help finding somthing. Leader Desslok Parkflyers 2 Jun 21, 2002 12:38 PM
Looking for an electric sailplane, need some help. Edwin Electric Sailplanes 0 Jun 02, 2002 04:02 PM
Ok guys I need a little help Speedfreak Scratchbuilt Indoor and Micro Models 5 Feb 11, 2002 03:23 PM
charging rate (need a little help) papichulo Power Systems 3 Jun 16, 2001 01:05 AM