New Products Flash Sale
Thread Tools
Old Mar 29, 2005, 08:17 PM
screamin' eagle is online now
Find More Posts by screamin' eagle
R/C Chronic
screamin' eagle's Avatar

Damaged MiniBlade Wing - How to Repair?


I just bought a used MiniBlade with some damage to the wing. How should I fix it? It apparently hit a sapling on final approach...

I was thinking carving some EPP to fill the void, and then covering with glass cloth. Yay? Nay?
Sign up now
to remove ads between posts
Old Mar 29, 2005, 08:23 PM
SUR DEVO is offline
Find More Posts by SUR DEVO
Registered User
SUR DEVO's Avatar
ouch! I just ordered a new Mini Blade, yesterday. this topic may be handy. I would think EPP/glass or CF/and resin would work just fine.
Old Mar 29, 2005, 08:29 PM
steve wenban is offline
Find More Posts by steve wenban
Crikey never leave beer behind
steve wenban's Avatar
Nay
cut the damage to a neat square cut some eps block to fit mark and sand to airfoil shape
pu glue in place abrade small surronding area replace sheeting over clean cut area fill voids as required cut lead edge to give an over lap on each edge of damaged area once blended to shape either glass and bag it if you have the equipement if not glass tissue about 4 layers sand back wing repaint entire panel
IMHO
SteveW
Old Mar 29, 2005, 09:53 PM
djklein21 is offline
Find More Posts by djklein21
Challenge is rewarding
djklein21's Avatar
Exactly, but dont cut a square shape, cut an oval or circular shape to reduce stress concentrations and reduce cracking in the future.
Old Mar 29, 2005, 09:57 PM
TFLG is online now
Find More Posts by TFLG
Registered User
TFLG's Avatar
EASY!
Send it and a check for $100 to TAWG

TFLG
Old Mar 29, 2005, 10:14 PM
Tawg is offline
Find More Posts by Tawg
Moderatee buncha places
Tawg's Avatar
TFLG is starting to sound like a pee-eye-em-pee
Old Mar 29, 2005, 10:28 PM
steve wenban is offline
Find More Posts by steve wenban
Crikey never leave beer behind
steve wenban's Avatar

correct


Quote:
Originally Posted by djklein21
Exactly, but dont cut a square shape, cut an oval or circular shape to reduce stress concentrations and reduce cracking in the future.
thanks I dont know what I was thinking round edges no stress raisers
SteveW
Old Mar 30, 2005, 12:00 AM
InTheLift is offline
Find More Posts by InTheLift
It could happen...
InTheLift's Avatar
Somewhere on the boards is a thread about doing a similar repair to a Miraj wing...I think it was a Miraj, but anyway, it's a good thread for the info. Might be worth a search. Covers cutting a chunk of EPS, glassing, etc for the repair. Also a bit of info about jigging the wing to keep it all lined up.
Old Mar 30, 2005, 12:09 AM
InTheLift is offline
Find More Posts by InTheLift
It could happen...
InTheLift's Avatar
Score!

Here's the thread I was referring to:

https://www.rcgroups.com/forums/show...ht=wing+repair
Old Mar 30, 2005, 12:20 AM
hydrogin is offline
Find More Posts by hydrogin
Registered User
Quote:
Originally Posted by steve wenban
thanks I dont know what I was thinking round edges no stress raisers
SteveW
Still, that was a very informative .... sentence


Lance
Old Mar 30, 2005, 12:30 AM
screamin' eagle is online now
Find More Posts by screamin' eagle
R/C Chronic
screamin' eagle's Avatar
Wow, my head is still spinning from the Miraj wing repair thread.... Unbelievable. Luckily the damage to the MiniBlade wing is much more manageable!
Old Apr 05, 2005, 12:24 PM
screamin' eagle is online now
Find More Posts by screamin' eagle
R/C Chronic
screamin' eagle's Avatar
Update: So far so good. I CA'd two thin pieces of balsa sheeting in the hole, one on top and one on bottom, curved to fit the foil. This provided an easy base on which to lay glass. I started with a small piece of 2 oz glass and then covered it with fiberglass tissue, first CA'd in place and then saturated with epoxy/microballons. Then I began sanding.

The repair is very strong. I've sanded until the surface is more or less even and will keep going, but I can't seem to get it smooth. There are small ruts and ridges here and there. Is there a final coat of something I can put on that will sand smooth?
Old Apr 05, 2005, 12:42 PM
TFLG is online now
Find More Posts by TFLG
Registered User
TFLG's Avatar
BONDO!

Run down to Pep Boys get a can of "Bondo Ultimate". If they don't have the Ultimate you can use the regular Bondo. Make sure you don't get the stuff with the fiberglass in it. Apply a thin layer layer of the bondo and sand it off once it dries (takes about 10 minutes to dry.) Wet sand with 220 grit paper then prime and paint.

TFLG
Old Apr 05, 2005, 12:45 PM
screamin' eagle is online now
Find More Posts by screamin' eagle
R/C Chronic
screamin' eagle's Avatar
I thought about Bondo but figured it might be too heavy for a wing. I have a tube of Bondo Spot Putty. Any good?
Old Apr 05, 2005, 01:01 PM
TFLG is online now
Find More Posts by TFLG
Registered User
TFLG's Avatar
The spot putty is only good for filling very small pinholes and scratches. I suppose you could use it on larger areas but it's not very durable. It dents and chips real easy and if you put tape over it it will pull the spot putty right off the plane when you peal off the tape.

TFLG


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Question How to repair a built up wing? Mike C Beginner Training Area (Aircraft-Electric) 3 May 19, 2004 10:52 PM
How to repair aerobird wing? magohn Beginner Training Area (Aircraft-Electric) 4 Jan 23, 2004 03:15 PM
Help! Miniblade wing repair tips? DaveyDave Slope 11 Nov 15, 2003 02:43 PM
Help! How to repair carbon fiber wing? jhurault The Builders Workshop 1 Nov 12, 2003 01:20 PM
How to repair hollow molded wing??? TheTick Slope 16 Jul 09, 2003 01:51 AM