Hi
Good news for the 28xx and 35xx Badass series
Very complete information on the detailed prop charts.
Specially no-load Io(A) for 4 voltages.

I am waiting for the future 23mm and 45mm stator series

Regarding the 28xx series :
I note that the bolt-on adapter mounting is 3 threaded M2.5 on circle 13mm
My preference is 4 threaded M3 on circle 12mm to match direct mount of some propellers like T-Motor polish carbon (2 holes 3mm spaced 12mm)
Like Scorpion M3011 , T-Motors MN3110 ... 4M3 on circle 12mm
Louis

Hello Louis,

It is good to hear from you again! The first batch of BadAss motors are designed for use in aircraft, and because of this, they do not lend themselves well to use in multirotors due to the higher Kv values.

If there is demand for them, we will produce multirotor specific motors and those will certainly have the mounting options for all of the popular styles of multirotor props.

Best Regards,

Lucien Miller

President & CEO
Innov8tive Designs, Inc.

Where are the prop charts on the site? no link at bottom and search can't find it?

Motors and esc look good. ZTW is good mfg with reasonable prices for the programmers. Did you spec firmware or just use theirs with component specs?

Here is a link to one...https://badasspower.com/pub/propchar...1300-Specs.htm
It is over the spec box.

You should consider a 2814-820KV to replace the popular Extreme Flight one. They go pretty fast used in classifieds. It works well on 48" 3D birds - I use one on my 3DHS Edge (Buck and a Half) and it's powerful.

+1!
The EF 48" air frames are amazing.
The Cobra 2820 840Kv, while a little longer weighs 3g less than the EF Torque motor. The performance with a 12-6 on 4S is all the performance I need on the 48" MSX!
The extra length can be compensated for by cutting out the center of the firewall, just leaving the blind nuts and securing the X mount to the back side of the blind nuts with the motor through the firewall. a washer and Nylock on the mounting screws will prevent the blind nuts from ever coming loose.
Great to see these new offerings from Innov8tive!
Pete

found it- have to click on performance data chart. Thanks!

Cobra Motor is not bad- good price too. Bad A** are about 50% more so interesting to see how they hold up. I like the shaft options on these too. Lots of parts/spares it looks like.

I don't know about everyone else but I'm putting my vote in for a multirotor version.
How badass would it be to have badass motors on your quad?

The answer is super badass. Just saying...

Hi
Just an idea to Lucien
It could be interesting to have a choice Delta or Wye connecting (same turns at the factory)
For example on three 2814-xxx (note I take the ratio 1.75)
a) BA 2814-870 --> Kv 497 rpm/V
b) BA 2814-1300 --> Kv 743 rpm/V
c) BA 2814-1950 --> Kv 1114 rpm/V
Just to get a larger Kv range & Kv number
Another indiscrete question : is the Badass factory the same as for Cobra (Danlions) ?
Louis

Here is my interview with Lucien about the new BadAss motor line...

RCGroups RC Upate - Innov8tive Designs - BadAss Motors Intro (36 min 50 sec)

As a longtime Scorpion and Cobra user, these new Bad Ass Motors and ESC’s look very nice, lots of great features and innovation.

You can’t beat Lucien ‘s service and the prop charts and information is the best. Looking forward to trying BA Motors and ESC’s......

Are those motor test results based on actual tests with propellers? Or are they calculated values? I just ran the numbers of the BadAss 350-890KV motor through Motocalc, and with the 4S LiPo and 10 to 12 inch diameter props, the motor calculations are very close to the BadAss publications.

(FYI, Motocalc suggests a maximum of 80 Amps for this motor.)