|
|
|
Discussion
1103 Toothpick Thing
I’m not quite sure what it is, but here it is! I’m hijacking the led signal for the servo. It’s almost ready to maiden, but needs software work. (And to detect my receiver...)
I have an AA for scale. |
|
|
|
|
|
|
So I got receiver working. Ibus is weird. I had to turn ppm on in the remote and use cli to enable ibus. So my current problem is servo. It has power, because when I turn or it will center itself, it just doesn’t listen. I used resource list and found the led strip to be on A01. So I freed A01 and set servo 1 to it and still nothing.
Edit: I probed the led pin on the processor and found it was b06. Changed it to that, no dice. Maybe the led pin is weird so I’ll try my ppm pin tomorrow. |
|
Last edited by Zentuckyfriedckn; Aug 15, 2019 at 10:56 PM.
|
|
|
|
Thanks. I have heard reports that they suck at smaller sizes but I have seen others do it with brushed quads.
|
|
|
|
|
|
A Banggood omnibus F4. I have motor 3 on the esc in the top left, motor 2 top right and motor 1 on the tail. I have the servo wired up to the 5v spot for an led strip. I plan on moving the signal wire to the unused motor 4 pin.
Link: https://banggood.app.link/s4K8gDMCcZ (I don’t think this is an affiliate link pls don’t kill me.) |
|
Last edited by Zentuckyfriedckn; Aug 16, 2019 at 10:16 AM.
Reason: Trimming
|
|
|
|
Don't move the servo signal to M4, that definitely won't work. The M1-M4 motors are resources B00, B01, A03, A02 respectively. They share 2 timer resources, which means you won't be able to set an ESC protocol for the motors and a pwm protocol for the servo. FWIW, here's the output definitions for the motors:
DEF_TIM(TIM3, CH3, PB0, TIM_USE_MOTOR, 0, 0), // S1_OUT D1_ST7 DEF_TIM(TIM3, CH4, PB1, TIM_USE_MOTOR, 0, 0), // S2_OUT D1_ST2 DEF_TIM(TIM2, CH4, PA3, TIM_USE_MOTOR, 0, 1), // S3_OUT D1_ST6 DEF_TIM(TIM2, CH3, PA2, TIM_USE_MOTOR, 0, 0), // S4_OUT D1_ST1 The LED pin is on a separate timer from the motors, and it's the pin you want to use for the servo signal. There's a number of Omnibus targets, I'm not sure which one this FC uses, but the resource could be either A01 or B06 depending on which target firmware is required. A01 is for the OMNIBUSF4 target, B06 is for the OMNIBUSF4SD target. Setting the servo 1 resource to one of these pin resources looks like it "should" work. |
|
|
|
|
|
I think LED_STRIP 1 is what I was missing I was trying to use the LED_STRIP resource. I need to change wiring, I already tried motor 4 before I saw your post.
|
|
|
|
|
|
I moved back to the led pin. No dice. Before soldering I confirmed that the led is connected to the processor. I think it was B06. I mapped servo 1 to one then the other. Nothing. The servo has power and will center itself but won’t communicate properly. I found that when I was Messing with using pin 4 I got the servo to spin. Continuously and uncontrolled. I’m running out of ideas servo tilt and channel forwarding are off.
EDIT: Here it is all buttoned up! Tail still doesn’t work, but a test hover showed I can at least fly it headless with no servo. |
|
Last edited by Zentuckyfriedckn; Aug 16, 2019 at 04:53 PM.
Reason: Kewl
|
|
|
|
Im going to hope into a different thread to fix servo to keep this thread clean for the (mostly) final unveil. When ready I'll delete this message and link to trouble shoot thread. Which is here --> https://www.rcgroups.com/forums/show...s#post42536807
|
|
Last edited by Zentuckyfriedckn; Aug 16, 2019 at 10:30 PM.
Reason: link
|
|
|
|
So I fixed servo issue but unveil is delays for another 3 weeks... See servo thread.
|
|
|
|
|
|
Nah. No concerns. For the short time it flew servo response was snappy. I’m using a little 4 gram analog servo.
Edit: it pulls less then 300 milliamps when stalled according to the seller. To contrast, my TX04 pulls 255-365 milliamps according to seller. |
|
Last edited by Zentuckyfriedckn; Aug 24, 2019 at 11:17 PM.
Reason: Current Values.
|
|
|
|
Hi there, what would the total cost be for this please - if I were to make my own?
|
|
|
|
|
|
I paid around 80 bucks for everything except transmitter, for cam and fpv goggles.
Edit: For a beginner though diy quad is probably more suitable. If you are bad at soldering then buy a prebuilt or practice soldering. Trust me. Tricopter is quite advanced and workaround heavy. Aka this thing exists as a challenge. In fact Betaflight is going to axe tricopter support soon I think. |
|
Last edited by Zentuckyfriedckn; Aug 25, 2019 at 10:33 PM.
|
Thread Tools | |
Similar Threads | |||||
Category | Thread | Thread Starter | Forum | Replies | Last Post |
New Product | GEPRC PHANTOM Toothpick Freestyle 2-4S FPV Racing Drone BNF/PNP F4 OSD 12A ESC 1103 M | alex_nikiforov | Banggood.com | 4 | Jul 16, 2019 06:55 PM |
Discussion | Большая Бензиновая Бойцовка 32сс | Urri | Russia | 2 | Aug 27, 2011 06:22 AM |