|
|
Thread OP
|
Discussion
SABAVIO KR84 Tortuga
Just got this in.
Please post your setups here. If anyone would like closeups please let me know and I will post. |
|
|
|
|
|
Thread OP
|
Coming soon
|
|
|
|
|
Thread OP
|
|
|
|
|
|
Thread OP
|
The size is slightly larger than a Funjet.
My setup so far is MKS 6130 servos for the wings and MKS HV75K for the canards. Motor for now it's what I have HET 1W-40 ESC 100 lite with Jeti MUI BATT 4S 3000 70C NOT IDEAL I know.. So far kit quality look OK except for the cracks around the motor area Paint is a matte like finish. |
|
Last edited by DepecheMode; Aug 27, 2018 at 03:48 PM.
|
|
|
|
Thank you for starting the thread!
Got mine a week ago. Waiting on parts to start. Motor: Dr Mad Thrust (same as HET 2W-30) Prop/s: Will play with various ones later (4.75x4.75, 5x5, 6x4...) ESC: Castle Edge 100A Bat: HK Graphene 6S 3000mah 65C-130C Wing Servos: Turnigy TGY-777 Canard Servo: TGY-210DMH Plane very well built and great build instructions. Found one issue right off. The canard shafts were too small and don't get clamped by the coupler. Great support from BR in Italy though... New ones shipped 2 days ago and are to arrive today! |
|
|
|
|||
|
This is a new name for an old plane, the Baiojet. There are a lot of setups for the Baiojet if you search it.
One thing to know is that adding the canard moves CG 20mm forward, so if you are tail heavy, drop the canard and CG moves back 20mm. To go fast and still hand launch, go turbine!! larger props will cause torque problems. The little 6S parkflyer setup suggested by SAB is fine to hand launch though, not too bad torque on the 5" props. 6-7" is worse. Size, Only the T25 engine and initial testing...
|
||
|
Last edited by henke; Aug 23, 2018 at 07:16 AM.
|
||
|
|
|
DepecheMode,
If goal is single top speed passes followed by cool down glides, you will need at least Edge 130A ESC pushed well past 150A on ground. Don’t forget heat sink(s) for motor. G. |
|
|
|
|
Thread OP
|
Thank you.
I was thinking of doing a 6s setup as well as I have a kontronik 100A Jive...... |
|
|
|
|
Thread OP
|
Size next to a Fun jet
|
|
|
|
|
Thread OP
|
While I wait to see what SAB will do to fix my motor section I decided to get the servos ready.
I notched the servo frames so the wires will not kink. Also I think I have a linkage setup that will be strong and lite |
|
|
|
|
Thread OP
|
Here I have the servo and linkage dry fitted.
Now how do I glue the frame in strait. Note the servo and frame can not go in together. You glue the frame then mount the servo |
|
Last edited by DepecheMode; Aug 24, 2018 at 11:53 AM.
|
|
|
|
Thanks again Henke!
|
|
|
Thread Tools | |
Similar Threads | |||||
Category | Thread | Thread Starter | Forum | Replies | Last Post |
New Product | Tortuga - german F3J plane | FlipF5D | Multi Task F3X | 8 | Feb 15, 2015 09:18 PM |
Discussion | Tortuga??!! | Tappet | Multi Task F3X | 3 | Aug 09, 2010 05:33 PM |