You can also disable from the OSD this annoying battery OSD information

I just did a review on this little wonder as well. It's great but some issues.

URUAV UR65 Tiny Whoop Review, flight video and how to diagnose a failed motor (7 min 29 sec)

Be careful soldering the buzzer onto micro pads in middle of board, I toasted my board by heating nearby parts.

Originally Posted by pj23

Be careful soldering the buzzer onto micro pads in middle of board, I toasted my board by heating nearby parts.

Why you didn't play more with the ESC's buzzing feature ?

Just saw this special edition 20000Kv 2S compatible motors https://www.banggood.com/Racerstar-0...p-1323435.html

24g of thrust in 1S, 42g in 2S .... If only if the Crazybee could handle 2S LiPo

Originally Posted by SeByDocKy

Just saw this special edition 20000Kv 2S compatible motors https://www.banggood.com/Racerstar-0...p-1323435.html

24g of thrust in 1S, 42g in 2S .... If only if the Crazybee could handle 2S LiPo

no reviews?? looks good on paper anyway.

Originally Posted by SeByDocKy

Just saw this special edition 20000Kv 2S compatible motors https://www.banggood.com/Racerstar-0...p-1323435.html

24g of thrust in 1S, 42g in 2S .... If only if the Crazybee could handle 2S LiPo

They don't seem to come with the connectors at the ends of the motor cables though...

Originally Posted by SeByDocKy

Just saw this special edition 20000Kv 2S compatible motors https://www.banggood.com/Racerstar-0...p-1323435.html

24g of thrust in 1S, 42g in 2S .... If only if the Crazybee could handle 2S LiPo

Product page in banggood site describe that "Long life Japanese NMB ball bearings".
But from the picture it doesn't seem to have ball bearing, at least on bottom side.
and 2s capable?
I have a feeling that 16000KV/19000KV on 1s is too heavy load for small 1s battery so 2s is too much.

So far I'm skeptical about all these info, but not sure.

I skimmed this thread and I see few mentions of batteries but I didnt see this specific question.

If I have a load of 260mAh 1s HV in the normal stick style without the connector coming off a wire (BetaFPV Lipos), will those work? They are JST-PH2.0 but they have the connector directly attached to the lipo instead of on a lead. Wasnt sure if the lead on the UR65 would reach or need to be extended.

Thanks!

Originally Posted by treys1

I skimmed this thread and I see few mentions of batteries but I didnt see this specific question.

If I have a load of 260mAh 1s HV in the normal stick style without the connector coming off a wire (BetaFPV Lipos), will those work? They are JST-PH2.0 but they have the connector directly attached to the lipo instead of on a lead. Wasnt sure if the lead on the UR65 would reach or need to be extended.

Thanks!

There should be enough cable to reach the battery.

Originally Posted by treys1

I skimmed this thread and I see few mentions of batteries but I didnt see this specific question.

If I have a load of 260mAh 1s HV in the normal stick style without the connector coming off a wire (BetaFPV Lipos), will those work? They are JST-PH2.0 but they have the connector directly attached to the lipo instead of on a lead. Wasnt sure if the lead on the UR65 would reach or need to be extended.

Thanks!

mine barely makes it, i have to make sure the batt is place a certain way every time. nonetheless, it works.

Originally Posted by treys1

IIf I have a load of 260mAh 1s HV in the normal stick style without the connector coming off a wire (BetaFPV Lipos), will those work? They are JST-PH2.0 but they have the connector directly attached to the lipo instead of on a lead. Wasnt sure if the lead on the UR65 would reach or need to be extended.!

Mine just barely reached and I'd end up pulling on the solder joints pretty much every time I connected one of those batteries. Your best bet is to replace the power lead with a longer one, imo.

Originally Posted by ScottAllyn

Mine just barely reached and I'd end up pulling on the solder joints pretty much every time I connected one of those batteries. Your best bet is to replace the power lead with a longer one, imo.

come to think of it my solder joints recently broke (from twisting/stress at the joint).
I replaced with the connector that came with this pack of batteries.

https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

Originally Posted by SeByDocKy

Just saw this special edition 20000Kv 2S compatible motors https://www.banggood.com/Racerstar-0...p-1323435.html

24g of thrust in 1S, 42g in 2S .... If only if the Crazybee could handle 2S LiPo

Nothing new about them I have a set that's about a year old.

Originally Posted by turboed13b

Nothing new about them I have a set that's about a year old.

And how are good are they ?