New Products Flash Sale
Thread Tools
Old Dec 08, 2004, 10:42 PM
jlandis is offline
Find More Posts by jlandis
Registered User

Pictures


Here are a couple of pictures. Below is the radio gear installed. I tested the servo's and they seem to have a bit of jitter. Moving the EZ connects in to reduce the torque helped reduce it. I think the throw will still be enough.
Sign up now
to remove ads between posts
Old Dec 08, 2004, 10:44 PM
jlandis is offline
Find More Posts by jlandis
Registered User

Cowl


Here is a closeup of the cowl attached. Also, note the wheels. I was not happy with the GWS wheels so I got some new ones. I have used these on my estarter and the ROG are much more smooth with these typewheels.
Old Dec 08, 2004, 10:46 PM
jlandis is offline
Find More Posts by jlandis
Registered User

Other pictures


And a couple of other pictures of the nearly finished plane. I would attach the wings tonight for a final picture but will keep you waiting in anticipation. I worked all last night and am too tired to complete.
Old Dec 09, 2004, 09:34 AM
jlandis is offline
Find More Posts by jlandis
Registered User
Wind picked up this morning so no maiden today.
Old Dec 09, 2004, 10:06 AM
sa-10 is offline
Find More Posts by sa-10
Registered User
sa-10's Avatar

Dont forget to cycle your cells!


Nothing burns a maiden quicker then non cycled cells, with the exception of incorrectly reversed servos.

I hope your not going to fly on that cell pack that is in the picture. Are you?
Old Dec 09, 2004, 12:54 PM
jlandis is offline
Find More Posts by jlandis
Registered User

sa-10


Sure that is one of my best packs!
Actually that is a couple of old cordless phone batteries put together to give me a cheap 7.2v battery to use for testing servos, programming my Pixies, testing receivers. Guess you could call it my shop battery.
Old Dec 09, 2004, 12:55 PM
jlandis is offline
Find More Posts by jlandis
Registered User

Battery


The pack I will fly with is a 3S1P 1500mah lipo.
Old Dec 09, 2004, 01:29 PM
intermision is offline
Find More Posts by intermision
Rocket Surgeon
intermision's Avatar
I plan I getting some Kan 1050s to power my TM 400, what configuration should I get?
Old Dec 09, 2004, 02:39 PM
Ekim is offline
Find More Posts by Ekim
Linux addict
Ekim's Avatar
I carved out the battery bay and put in a hump pack
Old Dec 09, 2004, 02:56 PM
intermision is offline
Find More Posts by intermision
Rocket Surgeon
intermision's Avatar
Whay leyout would work so I wouldn'r have to carve out the bay?
Old Dec 09, 2004, 11:35 PM
jlandis is offline
Find More Posts by jlandis
Registered User

Too cramped


In trial fitting my plane tonight I noticed that the following picture with electronics does not work. The aileron servo hits the receiver when placed where it is in this picture. I am still trying to fit it together and will post a final picture later.
Old Dec 09, 2004, 11:36 PM
jlandis is offline
Find More Posts by jlandis
Registered User
Any thoughts on the chatter I am getting from these small (cheap/inexpensive) servo's?
Old Dec 10, 2004, 12:31 AM
thunder1 is offline
Find More Posts by thunder1
Registered User
I haven't heard much about the interflight 4.6g servos but a lot of the smaller servos have a reputation for being jittery.

Have you tried different servos in the same receiver/esc combo?

Try to use a dedicated receiver battery instead of the esc to eliminate the ESC as a suspect.
Old Dec 10, 2004, 12:43 AM
Tom Frank is online now
Find More Posts by Tom Frank
Dance the skies...
Tom Frank's Avatar
Quote:
Originally Posted by intermision
I plan I getting some Kan 1050s to power my TM 400, what configuration should I get?
I use 8-cell 2/3A packs in my GWS PT-17, and will do the same in my TM400 that is not yet built. Use either a side-by-side flat pack or a double-stick (4 cells end-to-end, two cells wide. The latter is just a tad shorter and also narrower, and is my favorite. I think it will still be necessary to remove a little foam on the upper underside of the pack cavity so the packs will slide in through the cockpit opening (I saw this in another thread), but this will fit the best and will get enough weight up forward for balancing with little or no clay (from what I've been told by others).
Old Dec 10, 2004, 12:44 AM
Tom Frank is online now
Find More Posts by Tom Frank
Dance the skies...
Tom Frank's Avatar
Quote:
Originally Posted by jlandis
In trial fitting my plane tonight I noticed that the following picture with electronics does not work. The aileron servo hits the receiver when placed where it is in this picture. I am still trying to fit it together and will post a final picture later.
This is the main reason I don't use end pin RX anymore!


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Help! Can anyone point me to a good GWS Tiger Moth 400 Build with pictures? Sparkorama Electric Plane Talk 8 Feb 05, 2006 04:12 PM
Help! Can anyone point me to a good GWS Tiger Moth 400 Build with pictures? Sparkorama Parkflyers 0 Jan 23, 2006 06:39 PM
Tiger Moth 400 build "scale details added" Cruzer Parkflyers 9 Feb 20, 2005 01:50 PM
Tiger Moth 400 Build fuzzyhead Parkflyers 0 Oct 24, 2004 08:34 AM
Tiger Moth 400 Build and Maiden Flight review AirWarriorBelgy Parkflyers 180 Aug 16, 2004 03:23 PM