Thread Tools
Apr 28, 2019, 08:26 AM
POLAND
RAFALR30's Avatar
For better cooling of the regulator I made an additional larger inlet (from a plastic teaspoon painted in silver) to the chamber with electronics.
Sign up now
to remove ads between posts
May 04, 2019, 10:08 AM
Registered User
Quote:
Originally Posted by edwen303
Ran into this on ebay, a little smaller for less than $40, unpainted shipped: https://www.ebay.com/i/132836823237?...3D132836823237
This is the one you found:
https://m.aliexpress.com/item/328506...Q1556982217312

https://www.ebay.com/itm/28in-Sukhoi...72.m2749.l2649

https://m.aliexpress.com/item/325816...Q1556982280590

For some reason your link didn’t work for me.
Last edited by darmar; May 04, 2019 at 10:17 AM.
Jun 06, 2019, 12:41 AM
Plane crazy
Tartago's Avatar
Quote:
Originally Posted by RAFALR30
For better cooling of the regulator I made an additional larger inlet (from a plastic teaspoon painted in silver) to the chamber with electronics.
Nice!
Jun 14, 2019, 08:10 AM
Do a Barrel Roll!
rcbif's Avatar
deleted
Jul 06, 2019, 03:09 PM
Registered User
edwen303's Avatar
Thread OP
Thanks to Mikey68 I finally actually own the Su 35, GForce 2450kv motor with 6x4.5x3 prop. Flew today with both Roaringtop 2200mah 35c and Graphene1300mah 45C, the second flight with HK DSM2 gyro/receiver, both handlaunched by cnchelicopter. 6x4.5x3 prop drew way over 300 W, and most flight was at half throttle. CG on the location of servos. 150% travel, 48% expo.
Very good vertical at full throttle. Gyro/rx greatly helped stability in 10 mph gust. Don't have flight footage as we were struggling with handlaunch.
I like the most is the Cobra-like maneuver: full throttle for one or two sec, then throttle back and full elevator or full elevator/aileron, watch her flip or turn on a dime.
Aug 31, 2019, 05:51 AM
Glow 😡 no no no
I bought the pnp version and when I flew everything came to hot, I lost interest but have picked it up again, needed to get air and out so using the plastic spoons did this.
It’s a shame they did have air exits into the jet tubes.
Aug 31, 2019, 04:34 PM
Glow 😡 no no no
Quote:
Originally Posted by edwen303
Have you tried that 1800kv motor on 4s? Sounds like it has some potential as the low current on 3s.
I am considering trying this on 4s, a flying buddy of mine is putting this in his durafly me 163, he tested the motor on 4s on 5.5x 5.2 3bl prop and it pulled 42 amps, it made me think that maybe a 3 bl prop might help with the noise.
Aug 31, 2019, 08:28 PM
Glow 😡 no no no
Decided to mix things up a little and put a 3bl 51499 prop on. These are the figures.


Quick Reply
Message:

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log Foamboard SU-27 SU-35 Flanker Dual 55mm carcynic Scratchbuilt EDFs 71 Mar 15, 2018 10:48 AM
su 35 pusher conversion supershuey Pusher Prop Jet Models 6 Dec 04, 2017 08:24 PM
New Product SU 27/35 from hobbyking bandetlol Foamy EDFs 9 Apr 12, 2017 11:33 AM
Discussion Su 35 3D pusher jet kiko popo Foamies (Scratchbuilt) 11 Mar 05, 2014 02:57 PM
Discussion 3D su 35 pusher jet kiko popo 3D Foamies 2 Feb 28, 2014 11:36 AM