Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Sep 07, 2004, 01:45 PM
rcnutt is offline
Find More Posts by rcnutt
Registered User

Phoenix 10 esc question


Do you unhook motor before you begin to program the Phoenix 10 esc? I didn't see anything about that in the instructions. RCNutt
Sign up now
to remove ads between posts
Old Sep 07, 2004, 01:53 PM
Dr Kiwi is offline
Find More Posts by Dr Kiwi
Registered User
Dr Kiwi's Avatar
You don't need to have the motor connected to do the programming - no aircraft either - just the battery, Rx and ESC on your workbench or on a table beside your easy chair! In fact you don't want the motor connected since you could get chopped up by the prop if you have the system sitting in your lap!

Cheers, Phil
Old Sep 07, 2004, 08:32 PM
gfcermak is offline
Find More Posts by gfcermak
gasless
It does not even need the battery if using PHX-Link. The USB cable supplies the necessary power for the device while being programmed.
Old Sep 08, 2004, 01:53 PM
rcnutt is offline
Find More Posts by rcnutt
Registered User
I did program it last night the way I think I want it. What was odd is there was no beeping sound ????? The light flashes seemed to be right though. Has anyone else out there had that problem? RCNutt
Old Sep 08, 2004, 03:18 PM
iva is offline
iva
Find More Posts by iva
iva
Registered User
iva's Avatar
It will only beep if motor is attached. It uses motor windings as a loudspeker/buzzer.

Zoran
Old Sep 09, 2004, 11:43 AM
Eljimb0 is offline
Find More Posts by Eljimb0
Suspended Account
Quote:
Originally Posted by iva
It will only beep if motor is attached. It uses motor windings as a loudspeker/buzzer.

Zoran
AARRGGGGhh!
and all this time I thought it was me bad ears!!!

buccan ears??
jimbo
Old Sep 09, 2004, 01:56 PM
rcnutt is offline
Find More Posts by rcnutt
Registered User

hooking up motor before programming Pheonix 10


To Dr Kiwi, The instructions say you will here beeps. And I gather you must have your motor hooked up to hear beeps. So I assume that the motor will not turn if you are in the programming mode when you go to full throttle to answer "yes". Is this correct? Or is there some danger here? Anyone? RCNutt
Old Sep 09, 2004, 02:03 PM
pda4you is offline
Find More Posts by pda4you
Registered User
pda4you's Avatar
Quote:
Originally Posted by rcnutt
To Dr Kiwi, The instructions say you will here beeps. And I gather you must have your motor hooked up to hear beeps. So I assume that the motor will not turn if you are in the programming mode when you go to full throttle to answer "yes". Is this correct? Or is there some danger here? Anyone? RCNutt
The motor will not run in programming mode. I always program with the motor connected and get the beeps and just don't attach a prop for safety.

Mike
Old Sep 09, 2004, 02:04 PM
csisfun is offline
Find More Posts by csisfun
Balsa!!!
Quote:
Originally Posted by iva
It will only beep if motor is attached. It uses motor windings as a loudspeker/buzzer.

Zoran
EH?????????????????? That's new!


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
F/S Hacker B20-31S in GWS "A" Box w/ Phoenix 10 ESC Aobid Aircraft - Electric - Airplanes (FS/W) 13 Nov 17, 2003 11:46 PM
FS ASTRO 010 16T w/PHOENIX 10 ESC thangd Aircraft - Electric - Airplanes (FS/W) 2 Nov 12, 2003 11:43 AM
15L & Phoenix 10 programming question AirChopper Micro Helis 5 Jun 21, 2003 04:26 AM
Phoenix 10 ESC problem Tres Wright Power Systems 12 Jun 11, 2003 08:43 PM
WTB phoenix 10 ESC dstrout Aircraft - Electric - Airplanes (FS/W) 0 Mar 31, 2003 04:25 PM