Let's see them Eolo's! Post your pic and setup here :-)
Let's seem some Eolo's, we can post pics and setups and people thinking about one or have one that has questions about hop ups or elecs, we can ask eachother here. I guess I'll start...
Eolo Pro (cf blades, boom support, cf fins come stock! )
hs-85's on ccpm
hs-81 on the tail
Gy-401 gyro, gain at 60%
Airtronics 92778 rx
Hacker C40 12T w/stock 16t pinion
Kontronik Jazz 40-6-18
Tail drive ball bearing mod
Quick aluminum head
Quick aluminum swashplate
3rd bearing mod
aluminum anti rotation arm
-5 to +12 pitch range
throttle % at 97% straight across
8 cell GP 3300's, About 9.5 minutes of hover and 11 minutes or so with forward flight.
Last edited by Astro30; Sep 01, 2004 at 03:58 AM.
My Set Up
Hello, My EOLO goes like this.
EOLO Pro Kit
Twist 3700 with Jazz
3S4P TP gen 1
Third Bearing Kit mod
Tail drive bearings
Alu Swash Quick UK
Alu Servo upper mount
Alu Mixers (center holes)
Lightend paddles (stock mounts)
3 Hitech HS 85mg CCPM
Gy 401 with 9253
Pitch range +10 >< -10
Sorry no photos yet, no camera.
This one flies great and for 25 to 30 minutes.
Last edited by busted nut; Aug 31, 2004 at 12:58 PM.
hacker C40-8L 14t pinion
kontronik jazz/bec dis w/4.8v nicd
gy401 & s9253 tail
heliup boom support
heliup 3rd bearing anti rotation
heliup cf gyro plate
heliup servo holder
lightened paddles from rc hover
aluminum paddle holders
cf fin set
boom bearing upgrade
futaba 8 ch receiver
ms cf blades &white cf blade from rchover
this one's going to sit on the shelf while I master the stock eolo I am flying now. I don't want to crash too soon. also I'm looking into getting a custom paint job done on one of darths canopies .
Last edited by rcaddition; Sep 01, 2004 at 12:29 PM.
hitec eclipse 7 with spectra module
carbon MR blade,
cf finset with cnc aluminum clamp
Mega 22/20/2 with B50 heatsink and CC45
berg 6 dspIII receiver
3 hitec hs85
1 hitec hs5925mg digital servo on tail with futaba 401 gyro
3rd bearing (DIY)
tail drive bearing rotor guide with bearing
tail drive bearing block (UK QUICK)
CNC Servo Holder (Heliup)
CNC swash (UKQUICK)
CNC metal tailgear box
CNC Metal HEad Block
CNC aluminum mixing arm set
heliup gyro mount and tail rotor lever has been ordered.
Avoex Brushless motor
Kontronik Jazz 40-6-18
Kokam 1500HC 5S2P and Polyquest 2200 5S1P
3rd Bearing mod.
Quick Al BB Tail pinion Holder
Heliup Gyro support
Al. Paddle holder
DIY BB guides in Tail boom
Heliup CCPM servo holder
Heliup Tail support
Heliup landing gear supports
Futaba 9CHP and DP149 Rx
4 x hs-81
I'll try to remember all the add ons
Eolo Pro kit
CNC head block
CNC tail box
Heliup boom brace
Heliup gear braces
Heliup mixing arms
Heliup 3rd bearing
Heliup bb tail drive
Quick UK swash plate
Aluminum padle mounts
3 HS-85BB(soon to be upgraded to S3150's)
1 DS8417(to be replaced by a Volz Speed Maxx XP)
Berg 6 G3 RX
JR 8103 TX
Aveox 27/26/2, 14T pinion
5S Irate 1800 packs
Astro the money for the CNC tail box might be better spent on a better tail servo, before I switched to my 8417 I had an HS-81 on the tail and a full power climb out would drive the tail to the right since I put the better servo in it holds much better. Unless you suspect a problem from the plastic tail box?
ok. no I don't have any problems with my tailbox and in fact for my sport flying, my tail holds fine with the hs-81, it does kick slightly on full climb out punches but I can live with it for now. I just think the aluminum tail box looks super sweet. I do plan on upgrading the servo in the future though, I've been hearing about this Polo4? Know when that one comes out? I'll probably get that when it does. I'm sure I'll want to upgrade the tail servo as my flying starts to get more demanding.
btw. some people have tail rotor gear box twisting, I don't thave this prob but does the aluminum tail gear box prevent this?
That dual boom support and mounts also look a lot more effective than the Eolo pro one, I may want to do that one too. Whew, too many cool goodies for this bird. This hobby just hurts the pocket
Last edited by Astro30; Sep 01, 2004 at 04:00 AM.
Ya if your after the BLING the CNC tail box has plenty of it I havent had my box twist in flight but I have had two rough landings that twisted it and broke other parts as well so I guess I would expect it to twist It is easy to get carried away with bling on the Eolo they just look so good when you get them all decked out!!
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Let's See the 1/144's||Holycow||Scale Boats||7||Dec 18, 2005 08:12 PM|
|Post your Hornet Setup...||ThomasJoehnk||Micro Helis||29||Sep 19, 2005 03:28 AM|
|Post Your Corona Setup/Radio||Mr_Bazball||Electric Heli Talk||106||Sep 14, 2004 10:16 PM|
|Post your XBOW Setup||Depdog||Foamies (Kits)||3||Jan 31, 2003 06:07 PM|
|Post Your FROG Setup||Depdog||Foamies (Kits)||13||Jan 25, 2003 04:28 PM|