Check this out: http://www.justfly.solutions/index.php/apps

Her you can get Apps for your Taranis.

Just get the App you want, copy the content of the two ZIP files your receive by mail to your transmitters SDCard, and restore the AppMan model (or any other model provided by JustFly.solutions) in your model setup screen.

Apps available right now are:

• EngRev: adds a safe engine reverser to your existing waterplane model with a special BEC
• JustFly: graphical flight logging and flight timer
• F3KTrain: a complete training application for F3K pilots

Long press the PAGE button to start your new Apps:

EngRev:


JustFly:





F3Ktrain:



have fun and

Just Fly!

Hello there!

If I am using the app on my thermal plane, my SH switch is currently the motor "arm". Can I use the SH pull switch as the activation for the timer as well at the same time? Im worried that one switch can't be used for multiple functions.

Thanks so much!

Eric

Originally Posted by sdcfish

Hello there!



If I am using the app on my thermal plane, my SH switch is currently the motor "arm". Can I use the SH pull switch as the activation for the timer as well at the same time? Im worried that one switch can't be used for multiple functions.



Thanks so much!



Eric

No problem at all. The justfly app just looks at the state of the SH switch to determine when to start. It does in no way interfere with your model settings, apart from claiming timer control

You can change the switch used for starting the timers in one of the settings menus.

See https://www.justfly.solutions/index....apps/87-timers

That’s great. Thanks again!

Hello everybody,

I try to set up the throw of the Ailerons on my CX5 Dlg but I can't get it.
I want 8mm up and 14mm down throw.
I can't get them syncronized, one time left is okay, then right don't fits and flaps came mess.
I using multif3k.
Someone with a solution

Thank you and greetings from Germany
PANA

Hello,

I updated openTX to 2.3.9 (taranis x9d) and latest version od JustFly AppMan 5.4.
I installed multiF3k model and restored it.
But taranis is constantly beeping just like in trim mode - but on display i hawe cruise. When going to /Multi/flightmodes - I'm getting: Sorry, an error.

Changing flight modes dont work.

Please have someone solution?

Originally Posted by GreekAirRiot

Hello everybody,

I try to set up the throw of the Ailerons on my CX5 Dlg but I can't get it.
I want 8mm up and 14mm down throw.
I can't get them syncronized, one time left is okay, then right don't fits and flaps came mess.
I using multif3k.
Someone with a solution

Thank you and greetings from Germany
PANA

Hi, make sure you use the flaperon offset (or aileron offset if you choose to use ailerons as flaperons) to get the proper offset.

It is very important to FIRST get the center of the travel to correspond with the center position of the outputs menu. In your case, make sure that the center point (no offset, and no flaps pulled (check throttle stick direction for your presence)) correspond to both flaps being at about 3 mm down!

Then set the endpoints to correspond to the 8 and 13 mm.

Then set the offset to get the ailerons in the right position for fast mode.

In principle, you should be fine then.

If you ailerons are physically completely different connected, you can adjust the points on curve on the servo output of one of the servos to align both.

If you can't get it to work, check www.justfly.solutions for the how-to topics.

Or send me a mail as reply to your order confirmation with your WhatsApp number and I'll contact you to work through it. I speak German.

Originally Posted by mat.mi

Hello,

I updated openTX to 2.3.9 (taranis x9d) and latest version od JustFly AppMan 5.4.
I installed multiF3k model and restored it.
But taranis is constantly beeping just like in trim mode - but on display i hawe cruise. When going to /Multi/flightmodes - I'm getting: Sorry, an error.

Changing flight modes dont work.

Please have someone solution?

Did you put all the switches in the up position to start with? And throttle zero (no flaps)? Correct mode (I have 2 and sometimes it switches to 1 on opentx update).

About the error, SDcard fragmentation can be an issue. Make a backup of the sdcard, reformat it, and put the files back on.

If it persists, contact me.

Thank you, I will try that 👍
Otherwise I know we're to find you 😁
Are you Guido?

Greets from Pana 🙃

Originally Posted by l shems

Did you put all the switches in the up position to start with? And throttle zero (no flaps)? Correct mode (I have 2 and sometimes it switches to 1 on opentx update).

About the error, SDcard fragmentation can be an issue. Make a backup of the sdcard, reformat it, and put the files back on.

If it persists, contact me.

Originally Posted by l shems

Hi, make sure you use the flaperon offset (or aileron offset if you choose to use ailerons as flaperons) to get the proper offset.

It is very important to FIRST get the center of the travel to correspond with the center position of the outputs menu. In your case, make sure that the center point (no offset, and no flaps pulled (check throttle stick direction for your presence)) correspond to both flaps being at about 3 mm down!

Then set the endpoints to correspond to the 8 and 13 mm.

Then set the offset to get the ailerons in the right position for fast mode.

In principle, you should be fine then.

If you ailerons are physically completely different connected, you can adjust the points on curve on the servo output of one of the servos to align both.

If you can't get it to work, check www.justfly.solutions for the how-to topics.

Or send me a mail as reply to your order confirmation with your WhatsApp number and I'll contact you to work through it. I speak German.

Originally Posted by GreekAirRiot

Thank you, I will try that [emoji106]

Otherwise I know we're to find you [emoji16]

Are you Guido?



Greets from Pana [emoji854]

Of course I'm Guido. Lol.

Please report back on any solution. That's what this thread is for.

Hey Guido 😁
I tried but I wasn't really successful 🙈
The Aileronthrows are okay I think, but now the flaps/break have only the same downthrow like Ailerons🤷‍♂️
Played along and tried but can't find solution.
Sometimes head is stucking at the easiest things 🙈😂

Greetz from Pana

Originally Posted by l shems

Of course I'm Guido. Lol.

Please report back on any solution. That's what this thread is for.

Originally Posted by GreekAirRiot

Hey Guido [emoji16]

I tried but I wasn't really successful [emoji85]

The Aileronthrows are okay I think, but now the flaps/break have only the same downthrow like Ailerons[emoji2369]

Played along and tried but can't find solution.

Sometimes head is stucking at the easiest things [emoji85][emoji23]



Greetz from Pana

Ok, Well, support without seeing is difficult.

Can you try to contact me by mail to exchange WhatsApp or Skype contacts so I can help you through it?

Hey I shems,
I want to say a big thank you for the fast support and work you're doing👍
After a helpfull phonecall I understood my incorrect thinking and now I got it working as I like to👍
Great App, keep going on, I appreciate it much!

Sunny greetings
Pana

Originally Posted by l shems

Ok, Well, support without seeing is difficult.

Can you try to contact me by mail to exchange WhatsApp or Skype contacts so I can help you through it?

Originally Posted by mat.mi

Hello,

I updated openTX to 2.3.9 (taranis x9d) and latest version od JustFly AppMan 5.4.
I installed multiF3k model and restored it.
But taranis is constantly beeping just like in trim mode - but on display i hawe cruise. When going to /Multi/flightmodes - I'm getting: Sorry, an error.

Changing flight modes dont work.

Please have someone solution?

Hi mat, please contact me if you're still struggling.