Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Aug 12, 2004, 05:47 PM
zoom boy is offline
Find More Posts by zoom boy
I fly paragliders and RC

I need an all in one board for a feda dragonfly


Yes i know that I should go to seperates, but I like the way it flies woth the origional board. If any has upgraded their heli and happens to have this board laying around I would like to buy it.
Thanks
Mark
Sign up now
to remove ads between posts
Old Aug 12, 2004, 07:21 PM
Dr Honda is offline
Find More Posts by Dr Honda
Registered User
Dr Honda's Avatar
I have a PHA-01 sitting if you are interested in that. PM me.
Old Aug 12, 2004, 09:26 PM
Geoffrey109 is offline
Find More Posts by Geoffrey109
Blade Springs "Rock"
Doc, are you trying to make his life misrable...? At least offer a remady.....The 01 just sucks.....

G.
Old Aug 12, 2004, 09:27 PM
Silverstreak328 is offline
Find More Posts by Silverstreak328
Really Cool User
Silverstreak328's Avatar
I know! Seperates.
Old Aug 12, 2004, 09:37 PM
nevel64 is offline
Find More Posts by nevel64
Registered User
Iv'e got a 3 in 1 from smartech (aerohawk) lightly used works great! pm me if your interested
Old Aug 12, 2004, 09:44 PM
Silverstreak328 is offline
Find More Posts by Silverstreak328
Really Cool User
Silverstreak328's Avatar
I have one from a aerohawk too. Works perfect and has the 16 amp mosfet upgrade

I am still unsure if I am getting rid of it, after I get all my seperates install I'll know
Old Aug 13, 2004, 12:22 AM
zoom boy is offline
Find More Posts by zoom boy
I fly paragliders and RC
PMs sent.
Mark
Old Aug 13, 2004, 01:01 AM
monts is offline
Find More Posts by monts
Registered User
Quote:
Originally Posted by Silverstreak328
I have one from a aerohawk too. Works perfect and has the 16 amp mosfet upgrade

I am still unsure if I am getting rid of it, after I get all my seperates install I'll know
Does the new MOSfet stop the unwanted tail spinning?
Old Aug 13, 2004, 08:31 AM
Silverstreak328 is offline
Find More Posts by Silverstreak328
Really Cool User
Silverstreak328's Avatar
It lets you run bigger motors on the main motor.
Old Aug 13, 2004, 10:20 AM
Dr Honda is offline
Find More Posts by Dr Honda
Registered User
Dr Honda's Avatar
Quote:
Originally Posted by Geoffrey109
Doc, are you trying to make his life misrable...? At least offer a remady.....The 01 just sucks.....

G.
I never had the problems with the PHA-01. I set it up the way the GWS wants us to... and it flew fine. the key is to use the mix gain, and not the trim on the TX to center the tail. if you do that... it will fly perfect.

The only reson it was removed, was because I was setting my Aerohawk up with brusshless main and tail motors... so I couldn't use the electronics that came with my heli.

It's not the most user frendly thing I've used... but it works if set up right, and not pushed past it's current specs.

that's my story and I'm sicking to it.
Old Aug 13, 2004, 10:33 AM
aerohawk1 is offline
Find More Posts by aerohawk1
micro mechanic
aerohawk1's Avatar
Quote:
Originally Posted by monts
Does the new MOSfet stop the unwanted tail spinning?
No,but in my experience,an aluminum boom will!
Funny...I had forgotten about that problem!

The sub micro that I am building will have a CF boom to start,along with my repaired 3in1,so I will run some tests on the gyro while it is happening(if it does).
Last edited by aerohawk1; Aug 13, 2004 at 10:35 AM.
Old Aug 13, 2004, 12:56 PM
Geoffrey109 is offline
Find More Posts by Geoffrey109
Blade Springs "Rock"
Quote:
Originally Posted by Dr Honda
I never had the problems with the PHA-01. I set it up the way the GWS wants us to... and it flew fine. the key is to use the mix gain, and not the trim on the TX to center the tail. if you do that... it will fly perfect.

The only reson it was removed, was because I was setting my Aerohawk up with brusshless main and tail motors... so I couldn't use the electronics that came with my heli.

It's not the most user frendly thing I've used... but it works if set up right, and not pushed past it's current specs.

that's my story and I'm sicking to it.
I stand corrected. I was thinking about a pg01 gyro.....????

G.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Wanted blade cp all in one board burro breath Aircraft - Electric - Helis (FS/W) 2 Dec 02, 2006 02:42 PM
For Sale: PHA 01 All in one board skeppley Aircraft - Electric - Helis (FS/W) 3 Sep 10, 2004 10:33 AM
Feda All-in-one board problem Chris07 Micro Helis 2 Nov 23, 2003 10:35 AM
Feda all in one board repairs Yukonho Micro Helis 7 Oct 08, 2003 06:22 PM
The lows and highs of eflight for a newbie (all in one day). f2racer Beginner Training Area (Aircraft-Electric) 5 Sep 10, 2001 11:53 AM