"LISA" New plane from Jurgen - Page 2 - RC Groups
Thread Tools
Jan 04, 2015, 04:53 PM
Registered User
Jürgen Be's Avatar
It looks very nice !
You`ve done a great job this time with 3mm Depron.
I´m pleased you got the build managed with the german language on the plans.
But in addition you got that little picturebook with the plans
I´m looking forward to your build.

Jürgen

The ready floats will look like this.....
Sign up now
to remove ads between posts
Jan 04, 2015, 06:53 PM
Retired CAD guy
birdofplay's Avatar
Jurgen,

This is a very sweet little plane.
Quite desirable and irresistible.

I will cut one for myself on my CNC machine.
I have included my layout on a 1000x700mmx6mm depron sheet.
All to accommodate the Grain that you specify on your plans.

There is so much room left on the sheet that I put ALL the parts,
regardless of material, on the cutting.
I'll use the depron parts as a templates for the hand cut ply parts

Thanks for the free plans.

Best

Bob Neitzke
Hoosier Cutout Service
Jan 04, 2015, 08:00 PM
Registered User
spaceinvader's Avatar
Hey Bob. Maybe you could work something out with Jurgen and offer these as kits.
Latest blog entry: VA Models Christen Eagle
Jan 05, 2015, 06:16 AM
Retired CAD guy
birdofplay's Avatar
Spacei:

I'm going to try one myself and see how I like it.

And YES , I was thinking about writing Jurgen to ask permission.

Maybe yet today.

Stay tuned

Bob
Jan 05, 2015, 06:23 AM
Registered User
Jürgen Be's Avatar
Hi Bob,

nice you like my design of LISA, Im looking forward to your build.

@ spaceinvader, there will be CNC-Kits available next days, containing all 3mm Depron parts. But only the Depron, no ply parts.
They can be purchased in the online shop of the editor of the german magacine "FMT" . A digital version of the magacine in english is available too.

http://www.vth.de/flugmodell-und-technik/

Jürgen
Jan 05, 2015, 06:33 AM
Retired CAD guy
birdofplay's Avatar
Ah I just wrote to you.

I had not seen this latest post.

I am sorry but I can't find the kit a the magazine site.
Is there a specific Link to the order page ?

Bob
Jan 05, 2015, 06:39 AM
Registered User
Jürgen Be's Avatar
Bob,

the kits are not in the list jet, it will take a few days, because it`s holliday season over here. The official release of the 02/15 magacine is january 8. So I think the kits will be available from then. When I get the link, I will post it here.

Jürgen
Jan 05, 2015, 06:44 AM
Retired CAD guy
birdofplay's Avatar
OK , I understand.

Best

Bob
Jan 05, 2015, 02:51 PM
Retired CAD guy
birdofplay's Avatar
Well everything cut as planned.

See Pix for details.

I used a .0625" dia bit ( 1/16")
Still the very sharp points on two parts got "eaten" but otherwise it looks pretty nice.

A bit cold here in the Midwest USA for building unless you are in the house.
My shop heater is not up to -14C - 6 F

The CNC can handle it, but, I'm not sure the glues will set properly.
Jan 05, 2015, 03:41 PM
Registered User
Jürgen Be's Avatar
The Depron parts look good, Bob.
Nice done!

Jürgen
Jan 05, 2015, 05:39 PM
Retired CAD guy
birdofplay's Avatar
Thanks, Jürgen .

I would most likely have to charge ~ $20 + Shipping.
Maybe the Magazine would approve IF I agreed to NOT SELL to the EU market.

Best

Bob
Hoosier Cutout Service
Jan 05, 2015, 06:03 PM
Registered User
Jürgen Be's Avatar
Hi Bob,

I think this will make it easier, I will tell them.
20$ + shipping to EU will nearly be the same price, as they take for the Kit over here , 39.-€ So it will make no sense to order in the US.

I will have a call on thursday, then I can tell you more.

Regards
Jürgen
Jan 05, 2015, 07:41 PM
Retired CAD guy
birdofplay's Avatar
Thanks, Have a good evening.
Jan 05, 2015, 07:55 PM
Slow Flyer
Crunch_327's Avatar
Jan 08, 2015, 06:01 AM
Registered User
Jürgen Be's Avatar

CNC Parts


Hi Bob,

I got the OK for you, see private message

How about your build?

Jürgen


Thread Tools