Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor

The Morgan Mill Battery Cartridge System

Check out this upgrade for the Carbon Z Cub.

Splash

Easily install and remove your lipos in your Carbon Z Cub.

The E-flite Carbon Z Cub is an awesome machine. It's big, it flies great and looks good in the air. Getting your batteries in and out can be a little tricky, especially if you have big hands. You can also mess up the foam around the opening. This is where the Morgan Mill tray comes in.

The Morgan Mill Battery Tray - RCGroups (3 min 30 sec)

Key Features

  • Replacement floor
  • Multi position cartridge rack
  • Easy in and out battery installation

Photos

The unit ships ready to glue together with regular CA and epoxy. This is a ten minute build that will save you a lot of frustration and will keep your CZC looking good. This is a well thought out design and I think if you fly the Carbon Z Cub it's a must have.

Learn more about the Morgan Mill cartridge system here.

Thread Tools
Old Aug 22, 2014, 09:26 PM
Matt Gunn is online now
Find More Posts by Matt Gunn
RCGroups Editor
Matt Gunn's Avatar
All this awesome Carbon Z Cub attention is killing me. I may have to buy one!
Administrator
Old Aug 22, 2014, 11:13 PM
MaydayMayday is online now
Find More Posts by MaydayMayday
Registered User
MaydayMayday's Avatar
Hey! I know this guy!

Gary is an awesome guy, I'm sure this is top quality.
Old Aug 29, 2014, 10:21 AM
Conehead is offline
Find More Posts by Conehead
Flutter-Bys are fun
Conehead's Avatar
Nice review Jim.

Conehead
Orrin Eldred
Old Nov 08, 2014, 04:38 PM
TX79 is offline
Find More Posts by TX79
Registered User

Morgan Mill Battery Tray Screws Question


How do you get the font screws out of the stockholder and then how do you get them back in? Putting them back in seems like it's even hard because of the gap in the new tray.
Old Nov 08, 2014, 05:06 PM
Jim T. Graham is online now
Find More Posts by Jim T. Graham
Administrator
Jim T. Graham's Avatar
I put in the front screws first. I have keep my allen drivers on a magnetic hanger so they are magnetized. I then put the screws on the driver some how got them in the front holes. I did this three different times so it can be done.
Administrator
Old Jul 23, 2015, 12:51 PM
Jeepworld2002 is offline
Find More Posts by Jeepworld2002
Registered User
hi Jim
did the rear end of your tray hit foam hump in the fuse ? Mine is a 1/4"to high from the rear screw holes going into the screw hole, its being held up in the air. Did you have to use longer screws? i ca ed mine together and it had a slight downward warp from the mill figured it wouldn't hurt, but now its interfering with mounting.
Any ideas with the exception of cutting foam ?? i guess i should use front 4 screws and mount a batt n cartridge and see if it flexing will matter or not. but it flexing may prevent the cartridge from even going in ??


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold SOLD,,Carbon Z Cub , with batteries, morgan mill battery tray, Kavan inflatable tires Airplane,Ed Aircraft - Electric - Airplanes (FS/W) 1 Jun 15, 2014 08:56 AM
Help! Bobcad v21 and 3D milling / pocket milling or.. invertmast CAD/CAM 10 Dec 12, 2013 12:46 AM
For Sale (4) Cartridges for Aearo Twin Cartridge Respirator $15 shipped Artsloper Aircraft - General - Miscellaneous (FS/W) 0 Nov 20, 2010 01:58 PM
Question Oil smoke system for an electric? Not a smoke cartridge e-sailpilot86 Electric Plane Talk 38 Jun 08, 2009 05:44 PM
Sold Phase 3 F-16 unstarted + Morgan Mill mod parts. Jon Craig Aircraft - Electric - Jets (FS/W) 3 Apr 17, 2009 12:13 PM