Mega Speed Shark (1M) by Nanoplanes.net **Maiden Video** - RC Groups
Thread Tools
Jul 18, 2014, 08:47 AM
Registered User
MikeRx's Avatar
New Product

Mega Speed Shark (1M) by Nanoplanes.net **Maiden Video**


Before you start blowing up Dave's mail with orders, know that this is a prototype, and that the production kits are pending the success of this build.
I will say it all looks good and should go together the same as the smaller Speed Shark.
The motor is a new Microdan 2510-3100kv, to be run on 4s.
I see this built and covered by weekend..
Here are the parts..

added vid to front..

Mega Speed Shark 1M prototype (5 min 9 sec)
Last edited by MikeRx; Jul 27, 2014 at 10:55 PM.
Sign up now
to remove ads between posts
Jul 18, 2014, 11:41 AM
Registered User
THESANDMAN's Avatar
sweet , hopefully it will be in production soon, I got tired of waiting on the rifle 1m to come in stock and this will fit the bill nicely ,
Jul 18, 2014, 12:31 PM
Registered User
MikeRx's Avatar
Here is a few hrs later!
With record low temps here, I will hurry to sanding this evening.
A high of 73 when it should be 100+??
Jul 18, 2014, 12:51 PM
Registered User
Yeeeeeeeeessssssssssssss!!!!!!!
Jul 18, 2014, 12:55 PM
Registered User
Built 2 speed sharks I'm ready, as in paypal ready, actually I know where Dave lives, gonna go camp on his front lawn....
Jul 18, 2014, 09:17 PM
Registered User
MikeRx's Avatar
Moving along..wing 80% sanded.
SS wing for comparo..
Jul 18, 2014, 10:06 PM
Registered User
will be nice to have a little more room, you gonna use the same ztw 85 amp controller? and what sevos for the wing?
Jul 18, 2014, 10:56 PM
Registered User
MikeRx's Avatar
Quote:
Originally Posted by hubcapsteve
will be nice to have a little more room, you gonna use the same ztw 85 amp controller? and what sevos for the wing?
Ztw Mantis 65 with D60s.

Not much more room..
The plane is stretched but not thickened.
2200 4s batteries should slide forward easier for cg.
This kit is light and stiff..
I am guessing 22-23.5ounce auw.. which makes it lighter loaded than smaller SS.
Jul 19, 2014, 12:09 PM
Registered User
THESANDMAN's Avatar
will it be able to run an inrunner
Jul 19, 2014, 12:55 PM
Registered User
havent heard dave chime in but what is the cost on this one, (like it matters) heeheee........
Jul 19, 2014, 10:51 PM
Registered User
MikeRx's Avatar
Taking my time. 90% sanded and weighing 7.5 oz, or 1.5 oz more than my last Speed Shark at this stage.
At 21.5oz auw, this will be light!
I will have this flying as soon as the rest of the gear arrives..
Jul 19, 2014, 10:57 PM
Registered User
MikeRx's Avatar
Quote:
Originally Posted by THESANDMAN
will it be able to run an inrunner
The nose is too short.. it is designed around the Microdan 2510 outrunner motor.
One could modify to fit inrunners with advanced building skills.
Jul 19, 2014, 11:00 PM
Registered User
The speed shark was such a fun build, really looking forward to sanding out one of these. Daves designs are truly a builders dream....
Jul 20, 2014, 02:09 AM
Registered User
THESANDMAN's Avatar
Quote:
Originally Posted by MikeRx
The nose is too short.. it is designed around the Microdan 2510 outrunner motor.
One could modify to fit inrunners with advanced building skills.
I would rather not try and reinvent the wheel .
the micro dan motor isn't expensive so , I can use the inrunner I have on something else . .
Jul 20, 2014, 04:31 PM
Registered User
NanoDave's Avatar
Looking good so far! Thanks again Mike!

Nothing is locked in stone at this point so keep in mind the specs and recommendations could change. I've also got to build one of these prototypes but looks like I'm a bit slower than Mike on getting this going.. =)

Also the MicroDan motor is also a prototype too so there are still lots of things to test and figure out. I'm trying to keep costs low enough to keep things real, Plus I put many of our other kits on sale too so this will be as reasonable as I can make it.

Thanks for the interest guys, I'll try to move this project along as quickly as I can.


Thread Tools