|
|
|||||
|
Thread OP
|
Discussion
ZMR 250 ZMR 180 carbon fiber frame
ZMR 250, the clone carbon fiber/glassfiber/hybrid fiber frame
 Buying Options USA: Quadrysteria http://www.quadrysteria.com/store/p4...dle%C2%A0.html ReadyMadeRc http://www.readymaderc.com/store/ind...ath=76_729_735 Platinum Hobbies http://goo.gl/oaennO MultiRotorMania http://goo.gl/pBcMMw MultiRotorSuperStore https://www.multirotorsuperstore.com...uadcopter.html Team Legit http://goo.gl/ln2NGV BuddyRc http://goo.gl/MzB04l Canada HoverAll Frame : http://goo.gl/uxmZ6V Kit : http://goo.gl/Lw57zZ China TopRc http://goo.gl/filPTo I ordered two frames from these guys 3 months apart, both came in 1 week from china and weight about 140g GoodLuckBuy http://goo.gl/PHpEut MyRcMart http://goo.gl/AIOe3S customer service is questionable, buyers beware gregg from fpv tree racers broke this frame easily, the different bottom plate design could be questionable. Recommended Components Motors : SunnySky x2204s 2300kv or Cobra 2204 2300kv Esc: Emax 12a Simon series esc or BS Simonk Esc's ( please be aware these are known to have sync issues) Flight Controller: Naze32 acro Props (best): GemFan 5x3 or HQ 5x4 Props (insane): HQ 6x3 Props (nuts) : HQ 6x4.5 ( cobra 2204 1960kv motor preferred when running 4s) Battery(3s) : Turnigy Nano-Tech 1500mah 35c or Nano-Tech 1300mah 45c Battery(4s): Turnigy Nano-Tech 1300-1800mah 25c-45c Video
Insane setup : cobra 2204 1960kv running 65C batteries and 6 inch props
A good build post http://blog.oscarliang.net/cf-250-fr...uild-blackout/ BeeRotor 250 recently many have been modifying this frame to be low profile, a good alternative to consider is the bee rotor 250 frame http://rctimer.com/product-1540.html it not only comes with a PDB with LEDS and built in BEC and wiring for signal wires and micro minim osd. there are several tiny upgrades like better access to the standoffs, low profile for cleaner builds. |
||||
|
|
Last edited by CoolD; Jul 29, 2016 at 01:11 AM.
Reason: updating content
|
||||
|
|
|
|
|
|
|
...
|
|
|
Last edited by walkera2013; Oct 05, 2014 at 05:59 PM.
|
|
|
|
|
|
I got something similar from a seller "gadgetextreme" on ebay (which turned out to be goodluckbuy)
I was rather impressed with the overall quality. The cf weave was very nice compared to cf auto parts I've purchased, and the edges were smooth. I've yet to actually put it together, though. All the parts were there, down to the red spacers. |
|
|
|
|
|
|
|
|
I put mine together for some initial observations/inspections...
Still impressed with the overall quality of the cf. However, the nuts and bolts leave something to be desired. It did come with 1 extra bolt in each of the 2 sizes, and one extra nylock nut. The longer bolts to put the bottom and mid plates together are far too long. I got some cheap 1mm nylon washers from amazon to use as spacers, 3 of them seemed to create enough of a standoff to tighten the nylock nuts and not have a lot of wiggle room on the bottom plate. (http://www.amazon.com/gp/product/B00...?ie=UTF8&psc=1) It is this frame: http://untestedprototype.com/2013/09...t-mini-h-quad/ To satisfy my own curiosity, I grabbed my BO PDB to see how closely related they are, and they are very far apart. the BO PDB is longer, and slightly wider in some places. Holes don't line up really anywhere with any consistency, so don't plan on using them together. For about $60, I think it's a pretty decent frame. Time will tell, though. |
|
|
|
|
|
|
|
|
...
|
|
|
Last edited by walkera2013; Oct 05, 2014 at 06:00 PM.
|
|
|
|
|
|
|
|
|
